Push/Turn Studs and Receptacles
Features: Securely locks with the push of a thumb.
- To unlock, a ¼-turn is all that’s required in either direction. • No special tools. • Cannot be disengaged
accidentally. - Snap-in version permits high-speed assembly.
| Stud Assemblies Note: Part number shown are basic part numbers only. See ordering information for required dash numbers. |
 SlottedRecess |
Slotted |
 CrossRecess |
 CrossRecess |
| Material | (WitStandard * * ing) | Snap-in Version | Standard * * (With Retaining Ring) | Snap-in Version |
| Steel (Zinc Plated, Clear Chromate) | 79S01-[ ]-1AA | 79S01-[ ]-AA | 79S05-[ ]-1AA | 79S05-[ ]-AA |
| Steel (Cadmium Plated, Yellow Chromate) | 79S01-[ ]-1AB | 79S01-[ ]-AB | 79S05-[ ]-1AB | 79S05-[ ]-AB |
| Steel (Bright Chrome Plated) |
79S01-[ ]-1AC | 79S01-[ ]-AC | 79S05-[ ]-1AC | 79S05-[ ]-AC |
*S = .885 + (.394 x Dash No.)
* *Order retaining ring separately.
Receptacles
Standard Mount Receptacle
79R01 Series
Front Loading Snap-in Version
Install with ordinary thumb pressure.
79R02 Series
| Material | Part No. | Part No. |
| Steel (Zinc Plated, Clear Chromate) | 79RO1-1AA | 79RO2-[ ]-1AA |
| Steel (CadmiumPlated) | 79RO1-1AA | 79R02-[ ]-1AB |
Weight per 100 pieces: .95 lbs. (approximate) Weight per 100 pieces: .50 (approximate)
Typical Installation
| Recept acle Dash Number Select ion | ||
| F | A | Dash Numbers |
| .048 .036 | .080 .070 | -1 |
| .075 .054 | .106 .096 | -2 |
| .120 .090 | .150 .140 | -3 |
To Select Snap-in Receptacle Dash Number.
1. Determine “F” thickness.
2. Locate “F” thickness in table.
3. Find the corresponding dash number to the right.
How to Order:
“F” Thickness = .062
Receptacle Selected: 79R02-[?]-1AA
Dash Number From Table: -2
Complete Part Number: 79R02-2-1AA
 Hex Recess |
Hex Recess |
| Standard** (With Retaining Ring) | Snap-in Version |
| 79S07-[ ]-1AA | 79S07-[ ]AA |
| 79S07-[ ]-1AB | 79S07-[ ]-[ ]AB |
| 79S07-[ ]-1AC | 79S07-[ ]-[ ]AC |
Retaining Ring
| Part No. | Material | A | B | Weight |
| 15S11-1AC | Steel (Cadmium, Clear Chromate) | .013 | .030 | .030 |
| 15S11-1AD | Steel (Cadmium, Gold Chromate) | .013 | .030 | |
| 15S11-2AE | Ol Steel (Cadmium, e) | .018 | .035 | .045 |
Weights are in pounds per 100 pieces.
Retaining Ring Tool,
Part No. T107-1
See Ordering Information, Stud and Stud Cap Dash Number Selection on the following page.
Panel Preparation and Installation Data
Form through hole to .325-.330 diameter. Panels with thickness greater than. 134 inch must be back counterbored to a
concentric .590 inch diameter with a remaining material thickness of .134 inch max.
For retaining ring installa- tion, insert stud through panel and attach retaining ring
For snap-in style, place stud assembly on hole and push down to snap into place.
Frame Preparation forReceptacle Installation.
Standard Mount Receptacle
Top View Side View
Snap-in Receptacle
Top View Side View
Recessed Frame
Dimple frame as shown below to eliminate
.023 inch snap-in receptacle protrusion
Ordering Information/Stud and Stud Cup Dash Number Selection
To Select Stud Dash Number.
1. Determine “G”thickness.
Notes: (a) Increase “G” to allow for thickness of paint or other finishes and for the
compressed thickness of any gasket.
2. Locate “G” thickness in the table.
3. Then find the corresponding stud dash number.
4. When using snap-in style stud assemblies, specify the stud cup dash number corresponding to top
panel thickness “P”.
Standard Mount Version
Snap-in Version
How to Order:
Example 1.
(For stud assemblies using retaining ring) Stud Assembly Used: 79S01-[?]-1AA
“G” Total Thickness = .160 inch
Stud Dash Number From Table = -4
Complete Part Number: 79S01-4-1AA
Example 2.
(For snap-in style stud assemblies)
Stud Part Number Structure
“G” Total Thickness = .160 inch, Stud Dash Number From Table = -4, “P” Panel Thickness = .068 inch, Stud Cup Dash
Number From Table = -3, Complete Part Number: 79S01-4-3AA
| Stud Cap Dash Number Selection | |
| Px. | Dash Numbers |
| .065 | -2 |
| .099 | -3 |
| .133 | -4 |
| Stud Dash Number Selection | |
| *G Thickness | Dash Numbers |
| .039-.078 | – 1 |
| .079-.118 | – 2 |
| .119-.157 | – 3 |
| .158-.196 | – 4 |
| .197-.236 | – 5 |
| .237-.275 | – 6 |
| .276-.314 | – 7 |
| .315-.354 | – 8 |
| .355-.393 | – 9 |
| .394-.433 | -10 |
* Important Notes:
1. If the total thickness “G” is very near the top of the thickness range, selection of the next greater dash number is
For “G” thickness longer than those tabulated, contact the Camloc Products Division.