Extra Heavy Duty Stud Assemblies and Receptacles
(39F Series shown below; 34F Series shown on following page.)
Features: Capable of carrying high tensile loads and resisting mechanical damage under severe service
conditions. • A unique adjustable cross pin allows variable clamping loads and provides the ability to com- pensate for
variations in joint thickness as well as gasket set.
| 39F Series Stud Assemblies Note: Part numbers shown are basic part numbers only. See ordering information for required dash numbers. |
*S= 1.11 + (.25 x Dash No.) Hex Head |
 Handle Operated |
| Material | Part No. | Part No. |
| Steel (Cadmium Plated) | 39S01-[ ]-1AA | 39S08-[ ]-1AA |
Maximum Service Temperature: 450°F.
| 39F Series
Receptacles |
 Cross Pin |
Receptacle |
|||
| Material | Part No. | Weight (per 100 pcs.) (lbs.) | Part No. | Type | Weight (per 100 pcs.) (lbs.) |
| Steel (Cadmium Plated) | 39S02-1-1AA | 0.78 | 39R01-1-1AA | Rivet | 4.89 |
| Steel | – | – | 39R01-1-1AB | Weld | |
Specifications: Ultimate Tensile Strength: 39F Series-5000 lbs., 34E Series-10000 lbs.
Stud Grip Increments: .250 inch (39F and 34F). For other styles, materials or finishes, please contact the Camloc
Products Division.
Extra Heavy Duty Stud Assemblies and Receptacles
(continued)
(39F Series shown on previous page; 34F Series shown below.)
| 34F Series Stud AssembliesNote: Part numbers shown are basic part numbersonly. See ordering information for required dash numbers. |
Hex Head |
Handle Operated |
| Material | Part No. | Part No. |
| Steel (Cadmium Plated) | 34S01-[ ]-1AA | 34S08-[ ]-1AA |
| 34F Series
Receptacles |
Cross Pin |
Receptacle |
|||
| Material | Part No. | Weight (per 100 pcs.) (lbs.) | Part No. | Type | Weight (per 100 pcs.) (lbs.) |
| Steel (Cadmium Plated) | 34S02-1-1AA | 2.03 | 34R01-2-1BA | Rivet | 10.50 |
| Steel | – | – | 34R01-2-1BB | Weld | |
Stud Ejector Assembly/Components
(For use with 39F Series Stud Assemblies only)
| Component | Part No. | Df. | L | Weight (per 100 pcs.) (lbs.) | Material/ Finish | Max. |
| Spring | 39S09-1-1AA | .52 | 2.08 | 0.40 | Steel (Cadmium Plated) | 450°F. |
| Cup | 39S10-1-1AA | .75 | .291.284 | .050 |
Components
Stud Ejector Spring
Ejector Cup
Panel Preparation and Installation Data
Panel Preparation for Studs
Panel Preparation for Receptacle
| Dimen sio n s Fo r Pan el Prep aratio n | |||||
| Series | A Dia. Ref. | B Dia. Ref. | Cf. SRive g pacin | D Ref. | C’Sink |
| 39F | .531 | .78 | 1.250 | .156 | For 5/32″ Rivets |
| 34F | .688 | 1.020 | 1.620 | .188 | For 3/16″ Rivets |
Installing Weld Type Receptacle
Locate receptacle on center and weld in place as shown above.
Installing Stud
1. Insert stud through panel.
2. Using cross pin installation tool listed below, install cross pin.
3. When installation tool is pushed completely through stud, cross pin is automatically locked in place
and stud is captivated to panel.
| Installation Tools: | |
| For 39F | T137-1-1AA |
| For 34F | T135-1-1AA |
Cross Pin Adjustment
Adjust pin by rotating adjusting screw with hex key to achieve desired grip or compression load. Adjustment can be
accomplished with the assembly locked and loaded.
Important Note: If the 39F/34F Series is to be used without gaskets, a spring element
must be introduced to the joint. Contact the Camloc Products Division for additional information.
Installation (39F Series only)
1. Install spring over stud followed by spring cup.
2. Place assembly in panel and install cross pint to captivate.
Ordering Information/Stud Dash Number Selection
To Select Stud Dash Number
1. Determine “G” thickness.
Note: Increase “G” to allow for thickness of paint or other finishes and for the
compressed thickness of any gasket. When using ejector for 39F Series Studs, add .32 inch to “G” to determine stud dash
number.
2. Locate “G” total thickness in the table below.
3. Then find the corresponding stud dash number in the column to the right.
How to Order:
Example 1.
Stud Assembly Used: 39S01-[?]-1AA “G” Total Thickness = .825 inch, Stud Dash Number From Table = -3, Complete Part
Number: 39S01-3-1AA
(Note: If ejector is used, add .32 inch to “G”:, .825 + .32 = 1.145. Select -4 from table.)
Example 2.
Stud Assembly Used: 34S08-[?]-1AA “G” Total Thickness = .750 inch
Stud Dash Number From Table = -3
Complete Part Number: 34S08-3-1AA
| St ud Dash Number Select ion | |
| “G” Total Thickness | Dash No. |
| .250-.499 | -1 |
| .500-.749 | -2 |
| .750-.999 | -3 |
| 1.000-1.249 | -4 |
Stud Weights
| Stud Weight s (pounds per 100 pieces) | ||||
| Stud Dash Number | 34S01-[ ]-1AA | 34S08-[ ]-1AA | 39S01-[ ]-1AA | 39S08-[ ]-1AA |
| -1 | 14.70 | 21.21 | 6.35 | 8.40 |
| -2 | 16.40 | 22.31 | 7.45 | 9.43 |
| -3 | 18.20 | * | 8.45 | 10.46 |
| -4 | 19.90 | * | 9.55 | 11.49 |
*Contact the Camloc Products Division for availability.