Push Button and Push Panel Stud Assemblies and Receptacles
Features: One push locks. • Next push unlocks. • Push panel versions are concealed when door is closed.
15F Series. Stud Assemblies
Note: Part numbers shown are basic part numbers only. See ordering information for required dash numbers. |
Push Panel Mechanical Attachment |
Push Panel
Spot Weld Attachment |
Push Panel
Adhesive Attachment |
Material (Finish) | Part No. | Part No. | Part No. |
Steel (Cadmium, Clear Chromate) | 15S20-[ ]-1AA | 15S20-[ ]-2AA | 15S20-[ ]-3AA |
Steel (Cadmium, Gold Chromate) | — | — | — |
Steel (Bright Nickel) | — | — | — |
Steel (Black Phosphate) | — | — | — |
Steel (Zinc Plated) | 15S20-[ ]-1AC | — | 15S20-[ ]-3AC |
Steel (Cadmium, Clear Chromate) Except cage has no finish | 15S20-[ ]-1AB | 15S20-[ ]-2AB | 15S20-[ ]-3AB |
Brass and Steel (Chromium) | — | — | — |
Brass and Steel (Black Oxide) | — | — | — |
Note: All push panel versions shown here have stud pins which are free to swivel in
retainer cage. This feature helps compensate for misalignment between door and substructure.
Receptacle Retaining Nuts and Push-on Retainer |
Retaining Nut, Solid |
Retaining Nut, Sheet Metal |
Push-on Retainer | |||
Material (Finish) | Part No. | Weight (per 100 pcs.) (lbs.) | Part No. | Weight (per 100 pcs.) (lbs.) | Part No. | Weight (per 100 pcs.) (lbs.) |
Steel (Cadmium, Clear Chromate Plated) | 15R10-1AC | 0.23 | — | — | — | — |
Steel (Cadmium,
Gold Chromate Plated) |
15R10-1AD | — | — | — | — | |
Steel
(Zinc Plated) |
— | — | — | — | 15R16-1-1AA | 0.25 |
Steel (Zinc Plated, Clear Chromate) | — | — | 99N10-01A1 | 0.13 | — | — |
All specifications in inches unless otherwise specified. Contact the Camloc Products Division for par weights not
specified here.
Push Button |
Flush Push Button |
Part No. | Part No. |
15S1-[ ]-1AC | — |
15S1-[ ]-1AF | — |
15S1-[ ]-1AD | — |
15S1-[ ]-1AG | — |
— | — |
— | — |
— | 15S52-[ ]-1AA |
— | 15S52-[ ]-1AB |
Spacer: For stud dash no. 1 and 2 none required.
For stud dash no. 3 through 8 material nylon.
For stud dash no. 9 through 20 material brass, finish nickel plated.
Stud Retaining Ring
(For 15S1 and 15S52 Push Button Studs Only)
Part No. | Material (Finish) | A | B |
15S11-1AC | Steel (Cadmium, Clear Chromate | .013 .007 | .030 |
15S11-1AD | Steel (Cadmium, Gold Chromate) | .013 .007 | .030 |
15S11-2AE | Steel (Cadmium, Olive Drab Chromate) | .018 .012 | .035 |
Weight per 100 pcs.: 0.05 lbs.
Material (Finish) | Part No. |
Zinc (Zinc, Clear Chromate Plated) | 15R1-1AC |
Zinc (Zinc, Gold Chromate Plated) | 15R1-1AE |
Zinc (Black Phosphate) | 15R1-1AG |
Weight per 100 pcs.: 0.99 lbs
Large Flush Push Button Version
The studs and receptacle on this page are designed as a system and are not interchangeable with other studs or
receptacles in the 15F Series.
Note: Part numbers shown are basic part numbers only. See ordering information
Material (Finish) | Part No. |
Brass and Steel (Chromium) | 15S51-[ ]-1AA |
Brass and Steel (Black Oxide) | 15S51-[ ]-1AB |
Spacer: For stud dash no. 1 through 4 none required.
For stud dash no. 5 through 10 material nylon.
Stud Retaining Ring
Material (Finish) | Part No. |
Steel (Black Phosphate) | 15S47-1-1AA |
Receptacle
Material (Finish) | Part No. |
Brass (Nickel Plated) | 15R5-1-1AA |
Brass (Zinc Plated, Clear Chromate) | 15R5-1-1AB |
Receptacle Retainer Nut
Material (Finish) | Part No. |
Zinc (Zinc-Plated, Clear Chromate) | 15R4-1-1AB |
Zinc (Nickel-Plated) | 15R4-1-1AA |
Contact the Camloc Products Division for receptacle and retainer nut available in Brass (Nickel Plated) material.
15S51 Series. Panel Preparation and Installation Data
Panel Preparation and Installation Data
Panel Preparation For Studs Push Button Version
Determine panel thickness “P” and form through hole to .323 inch diameter.
Note: Panels with thickness greater than .188 inch must be back counterbored to a concentric .625
diameter with a remaining maximum material thickness of .188 inch.
Insert stud through panel and attach retaining ring.
Push Panel Version/ Mechanical Attachment
Locate centers and drill or punch holes for fastening method selected.
Install with 9/64 rivets or # size machine screws. Sheet metal or wood screws can also be used as appropriate
Push Panel Version/ Adhesive Attachment
Installation using adhesive backed stud assembly.
Push stud assembly into installed receptacle until stud assembly locks in place. Then peel off paper backing and close
door. Apply pressure to affix adhesive. Stud assembly is now installed.
Push Panel Version/Spot Weld Attachment
Located centers and spot weld in place.
Typical Installation, Locked Position.
Push panel stud assemblies require clearance to allow .170 inch free travel in order to function. Soft gaskets may be
used provided “P” panel can move .170 inch minimum before full compression is reached.
Note: For short length studs -6 and -7, spot weld or adhesive attachment is recommended to insure that
free travel zone is maintained.
Panel Preparation For Receptacles
Dimpled Panel
Drill .406 dia. hole then form to shape
Ordering Information/Stud Dash Number Selection
To Select Stud Dash Number
1. Determine “G” thickness.
Note: Increase “G” to allow for thickness of paint or other finishes.
2. Add. 015 inch to “G
3. Locate “G + .015” in table.
4. Note corresponding stud dash number.
For Push Button Version
Stud Dash Number Selection | |
G + .015 | Dash No. |
.030-.089 | – 1 |
.090-.149 | – 3 |
.150-.209 | – 5 |
.270-.329 | – 9 |
.330-.389 | -11 |
.390-.449 | -13 |
.450-.509 | -15 |
.510-.569 | -17 |
.570-.629 | -19 |
.630-.689 | -21 |
.690-.749 | -23 |
.750-.809 | -25 |
Important Note: If the thickness “G + .015” is very near the top of the thickness range, selection of
the next greater dash number is recommended. For “G + .015” thicknesses longer than those tabulated, contact the Camloc
Products Division.
For Push Panel Versions
Stud Dash Number Selection | |
G + .015 | Dash No. |
.18-.22 | – 6* |
.21-.25 | – 7* |
.24-.28 | – 8 |
.27-.31 | – 9 |
.30-.34 | -10 |
.33-.37 | -11 |
.36-.40 | -12 |
.39-.43 | -13 |
.42-.46 | -14 |
.45-.49 | -15 |
Important Note: If the thickness “G + .015” is very near the top of
the thickness range, selection of the next greater dash number is recommended. For “G + .015” thicknesses longer than
those tabulated, contact the Camloc Products Division.*Spot weld or adhesive attachment is recommended when using -6 and
-7 stud assemblies.
How to Order
Example 1.
(For 15S1 push button versions) Stud Assembly Used: 15S1-[?]-1AC “G” Total Thickness = .455 inch
Required Calculation: .455 + .015 = .470
Stud Dash Number From Table = .15
Complete Part Number: 15S1-15-1AC
Example 2.
(For 15S20 push panel versions) Stud Assembly Used: 15S20-[?]-1AA “G” Total Thickness = .350 inch
Required Calculation: .350 + .015 = .375 OR .38
Stud Dash Number From Table = .12
Complete Part Number: 15S20-12-1AA
Note: If the total thickness “G,” is very near the top of the thickness range, selection of the next
greater dash number is recommended. For “G” thicknesses longer than those tabulated, contact the Camloc Products
Division.
15S51 and 15S52 Stud Dash Number Selection
Stud Dash Number Selection | |
“G” Total Thickness | Stud Dash No. |
.047-.079 | -1 |
.079-.110 | -2 |
.110-.142 | -3 |
.142-.173 | -4 |
.173-.205 | -5 |
.205-.236 | -6 |
.236-.268 | -7 |
.268-.299 | -8 |
.299-.331 | -9 |
.331-.362 | -10 |