50F Series. General Purpose Stud Assemblies and
Receptacles
Features: Designed for use in agricultural, industrial, and similar environments where a simplified
rugged design is desired. • Studs are retained with a snap-in grommet or with optional retaining ring.
Note: Part numbers shown are basic part numbers only. See ordering information on Page A-41 for required dash numbers. |
Slo tted Recess | Cro ss Recess |
Material | Part No. | Part No. |
Stainless Steel (Passivated) | 50S10-[ ]-1BB | 50S10-[ ]-4BB |
Steel (Zinc Plated, Clear Chromate) | 50S10-[ ]-1AA | — |
Maximum Service Temperature: 450°F., except when plastic snap-in grommets are used.These styles are limited to 250°F.
*S = .429 + (.024 x Dash No.)
Plastic Knob Styles
Clip-on Receptacle
Basic Part Nos. Maximum Service Temperature: 250°F. Shank Material: Steel (Zinc Plated, Clear Chromate) |
||||
Black | Red | Grey | Beige | |
T-K n o b | 50S10-[ ]-6AC | 50S10-[ ]-6AD | 50S10-[ ]-6AE | 50S10-[ ]-6AF |
K n u rled K n o b | 50S10-[ ]-7AC | 50S10-[ ]7AD | 50S10-[ ]-7AE | — |
Clip-on Receptacle
Part No. | Material/Finish | Weight
(per 100 pcs.) (lbs.) |
Max Temp. |
50R4-1-1AA | Steel (Cadmium Plated, Gold Chromate) | 1.95 | 450 F. |
Specifications:
Ultimate Tensile Strength: 200 lbs. Stud Grip Increments: 0236 inch (0.6 mm) For optional styles, materials and
finishes, contact the Camloc Products Division.
Fixed Wing |
Fixed Offset Wing |
Part No. | Part No. |
– | – |
50S10-[ ] -2AA | 50S10-[ ]-3AA |
Plastic Snap-In Grommet
Order separately. Use to captivate stud assembly to panel. Eliminate need for retaining ring. Speeds assembly.
Part No. | L Ref. | D Dia. Max. | P. Max. | G Min. (see note) | Weight (per 100 pcs.) (lbs.) |
50S2-1-1AA | .140 | .348 | .062 | .032 | .035 |
50S12-1-1AA | .195 | .390 | .112 | .094 | .040 |
50S12-2-1AA | .245 | .162 | .144 | ||
50S12-3-1AA | .295 | .212 | .194 | ||
50S12-4-1AA | .345 | .262 | .244 |
Notes: 1. Grommets will protrude from the back side of panel. Minimum “G” thickness must be observed to
prevent grommets from jamming against the receptacle.
- Standard grommet color is white.
Retaining Ring
Order separately. Use to captivate stud assembly to panel in lieu of snap-in grommet.
Retaining Ring Installation Tool
P/N T98-1
50F Series. Panel Preparation and Installation Data
For Studs used with Snap-in Grommets
Determine panel thickness “P” and form through hole to corresponding “X” diameter. Panels with thicknesses greater than
.262 inch must be back counterbored to a concentric diameter of .438 inch with a maximum remaining material thickness of
.262 inch.
P | X |
up to .062 | .315-.320 |
.063-.162 | .350-.355 |
.163-.262 | .357-.362 |
Assemble stud with grommet and insert stud through panel
Tap stud with hammer to seat assembly into panel.
For Studs used with Retaining Rings
Form through hole to .370 inch diameter.
Insert stud through panel and attach retaining ring.
Frame Preparation for Receptacle Installation
Form .500-.520 through hole.
Important Note: Recommended “F” thickness range is .062-.188. The range can be extended to .032 to .219
at the extreme, however, installation problems may be encoun- tered.
Slide receptacle onto frame and locate on through hole.
Recessed Frame
Standard installation (illustrated above) will cause a minimum gap of .035 inch between panel and frame due to
receptacle protrusion. To eliminate gap, dimple frame to provide recess as shown.
50F Series. Ordering Information/ Stud Dash Number Selection
To Select Stud Dash Number:
1. Determine “G” total
Note: Increase “G” to allow for thickness of paint or other finishes, and for the compressed thickness
of any gasket.
2. Locate “G” in the table below.
3. Then find the corresponding stud dash number in the column designated for the
selected retention
How to Order:
Example 1.
(For stud assembly using retaining ring) Study Assembly Used: 50S10-[?] -1AA “G” Total Thickness = .155 inch Stud Dash
Number From Table = -7 Completed Part Number: 50S10-7-1AA
Example 2.
(For stud assembly using snap-in grommets) Stud Assembly Used: 50S10-[?]-1AA “G” Total Thickness = .155 inch Stud Dash
Number From Table = -9 Completed Part Number: 50S10-9-1AA (plus snap-in grommet selected)
St ud Dash Number Select ion | ||
*G | Dash Number For Studs Used With Retaining Rings | Dash Numbers For Studs Used With Grommets |
.055-.078 | – 3 | – 5 |
.079-.101 | – 4 | – 6 |
.102-.125 | – 5 | – 7 |
.126-.149 | – 6 | – 8 |
.150-.172 | – 7 | – 9 |
.173-.196 | – 8 | -10 |
.197-.220 | – 9 | -11 |
.221-.243 | -10 | -12 |
.244-.267 | -11 | -13 |
.268-.291 | -12 | -14 |
*Notes: 1. If “G” total thickness is very near the top of the thickness range, selection of the next
greater dash number is recommended. For “G” thickness greater than those tabulated, contact Camloc Products Division.
2.Grip ranges are based on 0.6 mm increments converted to nearest thousandth of an inch.
50F Series. Extra Heavy-Duty Stud Assemblies and Receptacles
Features: Rugged simplified design. * Particularly suited for use in adverse industrial and
agricultural environments. * Utilizes belleville washers for high preloads and enhanced vibration resistance.
Specifications: Ultimate Tensile Strength: 800 lbs. Stud Grip Increments: .0236 inch (0.6 mm).
Note: Part numbers shown are basic part numbers only. See ordering information on opposite page for required dash numbers. |
Slotted Recess | Fixed Wing |
Offset Fixed Wing |
Material | Part No. | Part No. | Part No. |
Steel Stud (Zinc Plated, Clear Chromate) Washer (Cadmium Plated, Clear Chromate) | 50S8-[ ] -1AA | 50S8-[ ]-2AA | 50S8-[ ]-3AA |
Maximum Service Temperature:*S = .429 + (.0236 x Dash No.)
Receptacles
Material | Part No. (with rivet holes) | Part No. (with weld nibs) |
Steel (Zinc Plated) | 50R3-1-AA | |
Steel (Oil Coated) | 50R3-1-2AB |
Basic Part Nos. Shank Material: Steel (Zinc Plated, Clear Chromate) Washer Material: Steel (Cadmium Plated, Clear Chromate) |
||||
Black | Red | Grey | Beige | |
T-Knob | 50S8-[ ]-6AC | 50S8-[ ]-6 AD | 50S8-[ ]-6AE | 50S8-[ ]-6 AF |
Knurled Knob | 50S8-[ ]-AC | 50S8-[ ]-7AD | 50S8-[ ]-7AE |
Snap-on Retaining Ring
Part No. | Material | Weight (per 100 pcs.) (lbs.) |
50S17-1-1AA | Steel (Cadmium Plated, Gold Chromate) | 0.10 |
Retaining Ring Installation Tool T98-1
Panel Preparation for Receptacle Installation.
50R3-1-1AA Standard Mount
Form .370 Dia. through hole. Insert stud through panel and attach retaining ring.
Panel Preparation for Receptacle Installation.
Drilled and countersunk rivet holes *Rivets Not Furnished. 50R3-1-2AB Weld Mount
Form .500 inch through hole. Locate receptacle on center and spot weld in place.
Ordering Information/ Stud Dash Number Selection
To Select Stud Dash Number.
1. Determine “G”
Note: Increase “G” to allow for thickness of paint or other finishes and for the compressed thickness of any gasket.
2. Locate “G” total thickness from the table below.
3. Then find the corresponding stud dash number.
How to Order:
Study Assembly Used: 50SB-[?]-1AA “G” Total Thickness = .246 inch Stud Dash Number From Table = -10 Complete Part
Number: 50S8-10-1AA
St ud Dash Number Select ion | |
“G” Total Thickness | Dash Number |
.020-.043 | – 1 |
.044-.066 | – 2 |
.067-.090 | – 3 |
.091-.113 | – 4 |
.114-.137 | – 5 |
.138-.161 | – 6 |
.162-.184 | – 7 |
.185-.208 | – 8 |
.209-.231 | – 9 |
.232-.255 | – 10 |
Important Note: If the total thickness “G” is very near the top of the thickness
range, selection of the next greater dash number is recommended. For “G” thickness longer than those tabulated, contact
Camloc. Products Division.