Installation and Tooling Selection
100 Series, Grommet Type
Permanently installed at sub-assembly, the 100 Series fasteners are self-retained through a telescopic press fit that is
a function of the sleeve and plug sections. The use of threaded or threaded self-locking type permits the attach- ment
of components without the use of additional lock nuts.
Panel Preparation
Requires the following:
1. A single diameter thru-hole
2. Standard drill sizes (comparable to body diameter). See table on opposite page
3. Access to both sides of the panel.
Fastener Installation
The most common method of applying the necessary pres- sure is the use of a hand arbor press, a hydraulic squeezer or
any pneumatically operated press.To assure proper alignment and to direct the pressure to the head of the fastener, the
use of a piloted anvil type tool as illustrated is suggested. Alignment tools such as these can be manufactured by your
own tooling facilities. Due to the simplicity of this type of tool Ros n does not stock them, but will make them to
order for any given type or size.An average of 1800 pounds for installation pressure is rec-ommended. Excessive pressure
may force the telescopic section to over-expand and become loose.Panel facing sheets up to .032″ will dimple
automatically to obtain a flush head condition. Thicker sheets may require the use of the non-flush head style fastener.
If flushness is required in these thicker facings, pre-dimpling or spot-facing is common practice in the
industry.Fasteners that cannot be installed by conventional methods (such as field installations), may be installed by
hand opera-ted pull up tools.
Installation Sequence
Tooling Part Numbers
Example: Insert Part Number 102C-10-1 requires Tool Kit Number: 1616-3.
| Fastener Series and Sizes | Installation Hole Size | Installation Tooling | ||
| Tool Kit Number | Pressing Anvil | Alignment Anvil | ||
| 101(*)12 | .290 | 1612 | 1612-1 | 1612-2 |
| 101C12 | 1615-1 | 1615-1-1 | ||
| 102(*)4 | .228 | 1613-0 | 1613-0-1 | 1613-0-2 |
| 102C4 | 1616-0 | 1616-0-1 | ||
| 102(*)6 | .290 | 1613 | 1613-1 | 1613-2 |
| 102C6 | 1616-1 | 1616-1-1 | ||
| 101(*)15 | 1614-2 | 1614-2-1 | 1614-2-2 | |
| 102(*)8 | ||||
| 101C15 | 1615-2 | 1615-2-1 | ||
| 102C8 | 1616-2 | 1616-2-1 | ||
| 101(*)18 | .323 | 1614-3 | 1614-3-1 | 1614-3-2 |
| 102(*)10 | ||||
| 101C18 | 1615-3 | 1615-3-1 | ||
| 102C10 | 1616-3 | 1616-3-1 | ||
| 101(*)25 | .390 | 1614-4 | 1614-4-1 | 1614-4-2 |
| 102(*)25 | ||||
| 101C25 | 1615-4 | 1615-4-1 | ||
| 102C25 | 1616-4 | 1616-4-1 | ||
| 101(*)28 | .421 | 1674 | 1674-1 | 1674-2 |
| 101c28 | 1676 | 1676-1 | 1676-2 | |
| 101(*)31 | .484 | 1614-5 | 1614-5-1 | 1614-5-2 |
| 102(*)31 | ||||
| 101C31 | 1615-5 | 1615-5-1 | ||
| 102C31 | 1616-5 | 1616-5-1 | ||
| 103(*)440 | .228 | 1617-0 | 1617-0-1 | 1617-0-2 |
| 104(*)440 | ||||
| 103(*)632 | .290 | 1617-1 | 1613-1 | 1617-1-2 |
| 104(*)632 | .323 | |||
| 106(*)632 | ||||
| 103(*)832 | .290 | 1617-2 | 1614-2-1 | 1617-2-2 |
| 104(*)832 | .323 | |||
| 106(*)832 | ||||
| 103(*)1032 | 1617-3 | 1614-3-1 | 1617-3-2 | |
| 104(*)1032 | .358 | |||
| 106(*)1032 | ||||
| 103(*)428 | .390 | 1617-4 | 1614-4-1 | 1617-4-2 |
| 104(*)428 | .421 | |||
| 106(*)428 | ||||
| 103(*)524 | .484 | 1617-5 | 1614-5-1 | 1617-5-2 |
| 104(*)524 | .515 | |||
| 106(*)624 | ||||
(*) Fill in ‘C’, ‘D’ or ‘F’ as applicable.
Pressing Anvils For ‘D’ ‘F’ Style Heads
Pressing Anvil For ‘C’ Style Heads
Alignment Anvils For Thru Hole Type Fasteners
Spring Loaded Alignment Anvils For Threaded Type Fasteners
