DETAIL SPECIFICATION SHEET
CAP INSERT, ASSEMBLY, PRESSURE SEAL, FLARED TUBE FITTING
INCH-POUND · AN929 Rev 14 w/Amendment 1 · 26 September 2024 · Superseding AN929 Rev 14, 29 August 2017 · AMSC N/A · FSC 4730
FIGURE 1. Cap dimensions and configuration.

FIGURE 1. Cap dimensions and configuration – Continued.
| Dash number |
Tube OD inches (mm) |
B dia. inches (mm) +.000 -.003 (0.08) |
C dia. inches (mm) |
D inches (mm) |
E inches (mm) |
|---|---|---|---|---|---|
| -2 | .125 (3.18) | .263 (6.68) | .156 (3.96) | .156 (3.96) | .125 (3.18) |
| -3 | .188 (4.78) | .325 (8.26) | .219 (5.56) | .219 (5.56) | |
| -4 | .250 (6.35) | .378 (9.60) | .281 (7.14) | .203 (5.16) | |
| -5 | .313 (7.95) | .441 (11.20) | .344 (8.74) | .219 (5.56) | .141 (3.58) |
| -6 | .375 (9.53) | .503 (12.78) | .422 (10.72) | .266 (6.76) | .156 (3.96) |
| -8 | .500 (12.70) | .683 (17.35) | .547 (13.89) | .313 (7.95) | .172 (4.37) |
| -10 | .625 (15.88) | .799 (20.30) | .672 (17.07) | .281 (7.14) | .250 (6.35) |
| -12 | .750 (19.05) | .974 (24.74) | .813 (20.65) | .313 (7.95) | |
| -16 | 1.000 (25.40) | 1.224 (31.09) | 1.063 (27.00) | .297 (7.54) | |
| -20 | 1.250 (31.75) | 1.536 (39.01) | 1.328 (33.73) | .375 (9.53) | |
| -24 | 1.500 (38.10) | 1.786 (45.36) | 1.594 (40.49) | .406 (10.31) | .375 (9.53) |
| -28 | 1.750 (44.45) | 2.161 (54.89) | 1.875 (47.63) | .500 (12.70) | |
| -32 | 2.000 (50.80) | 2.411 (61.24) | 2.141 (54.38) | .578 (14.68) | .500 (12.70) |
| -40 | 2.500 (63.50) | 2.911 (73.94) | 2.641 (67.08) | .625 (15.88) | .688 (17.48) |
| -48 | 3.000 (76.20) | 3.411 (86.64) | 3.156 (80.16) | .688 (17.48) |
| Dash number |
F dia. | G dia. inches (mm) +.000 -.005 (0.13) |
H inches (mm) |
R radius max inches (mm) |
|---|---|---|---|---|
| -2 | .094 (2.39) | .218 (5.54) | .531 (13.49) | .005 (0.13) |
| -3 | .156 (3.96) | .250 (6.35) | ||
| -4 | .172 (4.37) | .300 (7.62) | ||
| -5 | .234 (5.94) | .360 (9.14) | .563 (14.30) | |
| -6 | .297 (7.54) | .440 (11.18) | .625 (15.88) | .010 (0.25) |
| -8 | .391 (9.93) | .575 (14.61) | .750 (19.05) | |
| -10 | .438 (11.13) | .685 (17.40) | ||
| -12 | .563 (14.30) | .885 (22.48) | .875 (22.23) | |
| -16 | .813 (20.65) | 1.103 (28.02) | ||
| -20 | 1.078 (27.38) | 1.413 (35.89) | 1.000 (25.40) | |
| -24 | 1.313 (33.35) | 1.661 (42.19) | 1.125 (28.58) | |
| -28 | 1.547 (39.29) | 2.034 (51.66) | 1.375 (34.93) | .015 (0.38) |
| -32 | 1.781 (45.24) | 2.284 (58.01) | 1.438 (36.53) | |
| -40 | 2.000 (50.80) | 2.784 (70.71) | 1.750 (44.45) | |
| -48 | 2.500 (63.50) | 3.284 (83.41) | 1.813 (46.05) |
NOTES
- Dimensions are in inches.
- Metric equivalents are given for information only.
- Fittings shall be free of all burrs and slivers.
- Unless otherwise specified, tolerances for three point decimals ±.010 inch (0.25 mm).
- For design features purposes, this standard takes precedence over documents referenced herein.
FIGURE 2. Cap and nut assembly.

NOTE: Cap shall be movable and permanently secured to the nut to prevent assembly from coming apart, such as mechanical staking. The method used to prevent the movable cap from falling out of the nut is the manufacturer’s option. Other methods may be used upon approval by the Preparing Activity. A physical and permanent retention method shall be present. See figure 4 for examples of approved methods.
FIGURE 3. Cap assembly, safety chain configurations.

REQUIREMENTS
Dimensions and configurations: See figures 1, 2, and 3.
The Part or Identifying Number (PIN) represents a 2-piece assembly consisting of an AN818 nut and a permanently attached movable cap insert as specified herein and as shown on figure 2.
Material: See table I herein, procurement specification SAE-AS4841.
TABLE I. Material cap assembly.
| Cap insert assembly AN929 Material designator |
Cap insert assembly AN929 Material |
Cap insert assembly AN929 Alloy |
Nut AN818 2/ Material designator |
Nut AN818 2/ Material |
Nut AN818 2/ Alloy |
|---|---|---|---|---|---|
| F | Steel | 4130 or 4140 | Blank | Steel | 4130 or 4140 |
| J | CRES | 304 | J | CRES | 304 |
| K | CRES | 316 | K | CRES | 316 |
| S | CRES | 347 | J or K | CRES | 304 or 316 |
| T 1/ | Titanium | 6AI-4V | T | Titanium | 6AI-4V |
| W | Aluminum | 7075-T73 | W | Aluminum | 7075-T73 |
1/ Not for use with oxygen systems.
2/ Material designator for manufacturers use only to determine proper AN818 nut to use for the cap insert assembly.
Finish: See SAE-AS4841.
PART IDENTIFICATION NUMBER (PIN) SPECIFICATION
The PIN consists of the AN prefix, specification sheet number, “A” in place of dash for assembly with cap drilled for attachment of safety chain, blank or “L” for nut drilled with lock wire, number for assembly size, and a letter for material designator.
PIN Examples: AN929-8W identifies a cap assembly .500 inch (tube), 7075-T73 aluminum.
AN929-L8J identifies a cap assembly .500 inch (tube), AN818 nut drilled for lock wire, CRES 304.
AN929A8S identifies a cap assembly .500 inch (tube), cap drilled for attachment of safety chain, CRES 347.
AN929AL8J identifies a cap assembly .500 inch (tube), cap drilled for use with a safety chain, and AN818 nut drilled for lock wire, CRES 304.
SUPERSESSION DATA
The blank material designator for aluminum alloys 2014 and 2024 in table II have been replaced by a “W” material designator for aluminum alloy 7075-T73 due to stress corrosion cracking aluminum alloys 2014 and 2024.
TABLE II. Supersession data.
| Cancelled AN929 PIN |
Replacement AN929 PIN |
|---|---|
| AN929-2 | AN929-2W |
| AN929-L2 | AN929-L2W |
| AN929A2 | AN929A2W |
| AN929AL2 | AN929AL2W |
| AN929-3 | AN929-3W |
| AN929-L3 | AN929-L3W |
| AN929A3 | AN929A3W |
| AN929AL3 | AN929AL3W |
| AN929-4 | AN929-4W |
| AN929-L4 | AN929-L4W |
| AN929A4 | AN929A4W |
| AN929AL4 | AN929AL4W |
| AN929-5 | AN929-5W |
| AN929-L5 | AN929-L5W |
| AN929A5 | AN929A5W |
| AN929AL5 | AN929AL5W |
| AN929-6 | AN929-6W |
| AN929-L6 | AN929-L6W |
| AN929A6 | AN929A6W |
| AN929AL6 | AN929AL6W |
| AN929-8 | AN929-8W |
| AN929-L8 | AN929-L8W |
| AN929A8 | AN929A8W |
| N929AL8 | AN929AL8W |
| AN929-10 | AN929-10W |
| AN929-L10 | AN929-L10W |
| AN929A10 | AN929A10W |
| AN929AL10 | AN929AL10W |
| AN929-12 | AN929-12W |
| AN929-L12 | AN929-L12W |
| AN929A12 | AN929A12W |
| AN929AL12 | AN929AL12W |
| AN929-16 | AN929-16W |
| AN929-L16 | AN929-L16W |
| AN929A16 | AN929A16W |
| AN929AL16 | AN929AL16W |
| AN929-20 | AN929-20W |
| AN929-L20 | AN929-L20W |
| AN929A20 | AN929A20W |
| AN929AL20 | AN929AL20W |
| AN929-24 | AN929-24W |
| AN929-L24 | AN929-L24W |
| AN929A24 | AN929A24W |
| AN929AL24 | AN929AL24W |
| AN929-28 | AN929-28W |
| AN929-L28 | AN929-L28W |
| AN929A28 | AN929A28W |
| AN929AL28 | AN929AL28W |
| AN929-32 | AN929-32W |
| AN929-L32 | AN929-L32W |
| AN929A32 | AN929A32W |
| AN929AL32 | AN929AL32W |
| AN929-40 | AN929-40W |
| AN929-L40 | AN929-L40W |
| AN929A40 | AN929A40W |
| AN929AL40 | AN929AL40W |
| AN929-48 | AN929-48W |
| AN929-L48 | AN929-L48W |
| AN929A48 | AN929A48W |
| AN929AL48 | AN929AL48W |
FIGURE 4. Examples of approved methods of cap retention.

GENERAL GUIDANCE
Amendment notations. The margins of this specification are marked with vertical lines to indicate modifications generated by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations.