DETAIL SPECIFICATION SHEET
NUT, TUBE, BULKHEAD AND UNIVERSAL FITTING
INCH-POUND · AN924 Rev 14 · 15 February 2018 · Superseding AN924 Rev 13, 14 April 20104 · AMSC N/A · FSC 4730
FIGURE 1. Tube nut dimensions and configurations.

FIGURE 1. Tube nut dimensions and configurations – Continued.
| Dash number |
Tubing OD |
Thread T (Ref) SAE-AS8879 |
A (mm) |
A tolerance |
B (mm) |
|---|---|---|---|---|---|
| -2 | .125 | .3125-24UNJF-3B | .563 (14.30) | +.003 (0.08) -.004 (0.10) | .219 (5.56) |
| -3 | .188 | .3750-24UNJF-3B | .625 (15.88) | .219 (5.56) | |
| -4 | .250 | .4375-20UNJF-3B | .688 (17.48) | .250 (6.35) | |
| -5 | .313 | .5000-20UNJF-3B | .750 (19.05) | .250 (6.35) | |
| -6 | .375 | .5625-18UNJF-3B | .813 (20.65) | .266 (6.76) | |
| -8 | .500 | .7500-16UNJF-3B | 1.000 (25.40) | .313 (7.95) | |
| -10 | .628 | .8750-14UNJF-3B | 1.125 (28.58) | .359 (9.12) | |
| -12 | .750 | 1.0625-12UNJ-3B | 1.375 (34.93) | ±.016 (0.41) | .406 (10.31) |
| -16 | 1.000 | 1.3125-12UNJ-3B | 1.625 (41.28) | ||
| -20 | 1.250 | 1.6250-12UNJ-3B | 1.938 (49.23) | ||
| -24 | 1.500 | 1.875-12UNJ-3B | 2.188 (55.58) | ±.020 (0.51) | |
| -28 | 1.750 | 2.250-12UNJ-3B | 2.563 (65.10) | ||
| -32 | 2.000 | 2.500-12UNJ-3B | 2.813 (71.45) | ||
| -40 | 2.500 | 3.000-12UNJ-3B | 3.312 (84.12) | ||
| -48 | 3.000 | 3.500-12UNJ-3B | 3.812 (96.82) |
| Dash number |
C Dia. |
E Min. |
G ±.010 (0.25) mm) |
H Max (see note 5) (mm) |
|---|---|---|---|---|
| -2 | .313 (7.95) | .629 (15.98) | .500 (12.70) | .005 (0.13) |
| -3 | .375 (9.53) | .699 (17.75) | .562 (14.27) | |
| -4 | .438 (11.13) | .771 (19.58) | .625 (15.88) | |
| -5 | .500 (12.70) | .842 (21.39) | .687 (17.45) | |
| -6 | .563 (14.30) | .914 (23.22) | .750 (19.05) | |
| -8 | .750 (19.05) | 1.127 (28.63) | .937 (23.80) | |
| -10 | .875(22.23) | 1.270 (32.26) | 1.052 (26.72) | |
| -12 | 1.063 (27.00) | 1.555 (39.50) | 1.274 (32.36) | .008 (0.20) |
| -16 | 1.313 (33.35) | 1.827 (46.41) | 1.524 (38.71) | |
| -20 | 1.625 (41.28) | 2.184 (55.47) | 1.838 (46.69) | |
| -24 | 1.875 (47.63) | 2.465 (62.61) | 2.093 (53.16) | |
| -28 | 2.250 (57.15) | 2.892 (73.46) | 2.468 (62.69) | |
| -32 | 2.500 (63.50) | 3.178 (80.72) | 2.718 (69.04) | |
| -40 | 3.000 (76.20) | 3.747 (95.17) | 3.218 (81.74) | |
| -48 | 3.500 (88.90) | 4.318 (109.68) | 3.718 (94.44) |
NOTES
- Dimensions are in inches.
- Metric equivalents are given for information only.
- Unless otherwise specified tolerances are ±.016 inch (0.41 mm) angles ±0.5°.
- Break sharp edges .and remove all hanging burrs and slivers.
- Squareness between thread and face of hex shall not exceed H when measured at diameter G, both sides.
- Machined surfaces shall be finished to 125µin Ra, forged surfaces shall be 250µin Ra, unless otherwise specified on the figures. Surface finish shall be in accordance with ASME B46.1.
- For design features purposes, this standard takes precedence over documents referenced herein.
- Referenced documents shall be of the issue in effect on date of invitation for bid.
REQUIREMENTS
Dimensions and configuration shall be in accordance with figure 1.
Installation shall be in accordance with MS21344.
Materials shall be in accordance with SAE-AS4841, see table I for material and finish code.
Finish. Finishes shall be as specified in table I. All plating’s shall be capable of meeting a minimum of 96 hours salt spray test in accordance with ASTM B117. The fittings shall show no evidence of red corrosion after 96 hours of salt spray. Fluid passages, other openings and internal threads shall not be subject to the plating thickness requirement and may have bare areas provided they are protected with a light film of oil.
TABLE I. Material and finish identification codes.
| Material and finish code |
Material | Plating finish |
|---|---|---|
| Blank | Steel | Cadmium plating in accordance with SAE-AS4841 1/ |
| G | Steel | Zinc plating in accordance with ASTM B633; type V, Fe/Zn 8, 2/ |
| H | Steel | Zinc-aluminum in accordance with ASTM F1136/F1136M, grade 3, NC. 2/ |
| J | CRES type 304 | In accordance with SAE-AS4841 |
| K | CRES, type 316 | In accordance with SAE-AS4841 |
| L | Steel | Zinc-nickel in accordance with SAE-AMS2417, type 2, grade B 2/ 3/ |
| M | Nickel-copper alloy UNS N04400 | No additional finish. |
| N | High-chromium nickel alloy UNS N06690 | No additional finish. |
| P | Steel | Zinc phosphate finish in accordance MIL-DTL-16232 type Z, class1 4/ |
| R | CRES, type 321 | In accordance with SAE-AS4841 |
| T | Titanium 4/ | Anodize in accordance with SAE-AMS2488 type 2. |
| TF | Fluoride phosphate in accordance with SAE-AMS2486. 5/ | |
| W | Aluminum alloy 7075-T73 | In accordance with SAE-AS4841 |
| Z | Steel | Zinc plating in accordance with ASTM B695, type II, class 8. 4/ |
| ZN | Steel | Zinc may be any zinc plating from PIN codes G, L, and Z with a colored chromate coating. 4/ |
1/ Embrittlement test need not be run. Cadmium shall not be used in oxygen or potable water systems. Cadmium is prohibited from use in NAVSEA owned shipboard systems.
2/ Hexavalent chromium free. Finish shall be RoHS compliant.
3/ The zinc-nickel alloy plate shall contain 12% to 16% nickel. The coating thickness shall be 315µ inches (8µm) minimum.
4/ Not for use in aircraft. Requires approval from the Program Office for all applications.
5/ A pretreatment, a modification of the fluoride treatment, or a post treatment shall be applied so the final color of the fittings shall be similar to SAE-AMS-STD-595 colors 36076 through 36293. Titanium shall not be used in oxygen or potable water systems.
Trivalent wrenchability. When the finish has been damaged due to poor wrenchability, the surface of the fluid passage bolt shall be touched up using the brush plating process below. The term “trivalent wrenchability” is used to evaluate the ability of the finish to withstand abrasion from an excessive amount of wrenching.
Brush plating of NAVAIR TCP shall be in accordance with MIL-DTL-81706, type 2, class 1A, material form 1 through 6, application method B. Example of a PIN: M817062A6B.
Marking: Part shall be impression stamped with AN, material/finish designator, and include the manufacturers CAGE, name, or trademark on the hex side only.
Cadmium is not recommended. To the users of this document, it is recommended that the use of carbon steel material with cadmium plating be used only when other materials and finishes specified in this document cannot meet performance requirements.
Cadmium is prohibited from use in NAVSEA owned shipboard systems in accordance with the requirements of T9070-AL-DPC-020/077-2.
Class I and II ozone depleting substances (ODS) shall not be used in AN914 or any referenced procedures.
Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.
Referenced documents shall be of the issue in effect on date of invitations for bid.
PART IDENTIFICATION NUMBER (PIN) SPECIFICATION
The PIN consists of the letters “AN” the specification sheet number, a dash number for pipe nut tube size, and a material and finish code letter. Unassigned PIN’s shall not be used.
PIN example: AN924-4W indicates nut 1/4 inch tubing with aluminum alloy 7075-T73.
SUPERSESSION DATA
Due to stress corrosion cracking aluminum alloys 2014 and 2024 “D” designator has been replaced by aluminum alloy 7075 “W” designator example: AN924-4D use AN924-4W.
Metal cracking due to high temperatures CRES alloy 347 “S” designator has been replaced by CRES alloy 321 “R” designator. Example: AN9244S use AN924-4R.
AN924 and MS24400 CRES nuts of like size are physically interchangeable; however MS24400 nuts coded C cannot always replace AN924 nuts coded J or K and MS24400 nuts coded S cannot always replace AN924 nuts coded S.
Table II provides a detailed cross-reference of AN924 PINs and replacement SAE-AS5178 PINs. Users are cautioned to evaluate replacements for their particular application.
CAUTION: The superseding information is valid as of the date of this specification and may be superseded by subsequent revisions of the superseding document.
TABLE II. AN924 to SAE- AS5178 cross-reference data. 1/ 2/ 3/
| AN PIN inactive for new design |
Canceled AN PIN |
Tube Size |
Replacement AN PIN |
AS PIN for new design |
|---|---|---|---|---|
| AN924-2 | .125 | AS5178-02- | ||
| AN924-2D | .125 | AN924-2W | AS5178W02 | |
| AN924-2J | .125 | AS5178J02 | ||
| AN924-2K | .125 | AS5178K02 | ||
| AN924-2R | .125 | AS5178R02 | ||
| AN924-2S | .125 | AN924-2R | AS5178R02 | |
| AN924-2T | .125 | AS5178T02 | ||
| AN924-2W | .125 | AS5178W02 | ||
| AN924-3 | .188 | AS5178-03- | ||
| AN924-3D | .188 | AN924-3W | AS5178W03 | |
| AN924-3J | .188 | AS5178J03 | ||
| AN924-3K | .188 | AS5178K03 | ||
| AN924-3R | .188 | AS5178R03 | ||
| AN924-3S | .188 | AN924-3R | AS5178R03 | |
| AN924-3T | .188 | AS5178T03 | ||
| AN924-3W | .188 | AS5178W03 | ||
| AN924-4 | .250 | AS5178-04- | ||
| AN924-4D | .250 | AN924-4W | AS5178W04 | |
| AN924-4J | .250 | AS5178J04 | ||
| AN924-4K | .250 | AS5178K04 | ||
| AN924-4R | .250 | AS5178R04 | ||
| AN924-4S | .250 | AN924-4R | AS5178R04 | |
| AN924-4T | .250 | AS5178T04 | ||
| AN924-4W | .250 | AS5178W04 | ||
| AN924-5 | .312 | AS5178-05- | ||
| AN924-5D | .312 | AN924-5W | AS5178W05 | |
| AN924-5J | .312 | AS5178J05 | ||
| AN924-5K | .312 | AS5178K05 | ||
| AN924-5R | .312 | AS5178R05 | ||
| AN924-5S | .312 | AN924-5R | AS5178R05 | |
| AN924-5T | .312 | AS5178T05 | ||
| AN924-5W | .312 | AS5178W05 | ||
| AN924-6 | .375 | AS5178-06- | ||
| AN924-6D | .375 | AN924-6W | AS5178W06 | |
| AN924-6J | .375 | AS5178J06 | ||
| AN924-6K | .375 | AS5178K06 | ||
| AN924-6R | .375 | AS5178R06 | ||
| AN924-6S | .375 | AN924-6R | AS5178R06 | |
| AN924-6T | .375 | AS5178T06 | ||
| AN924-6W | .375 | AS5178W06 | ||
| AN924-8 | .500 | AS5178-08- | ||
| AN924-8D | .500 | AN924-8W | AS5178W08 | |
| AN924-8J | .500 | AS5178J08 | ||
| AN924-8K | .500 | AS5178K08 | ||
| AN924-8R | .500 | AS5178R08 | ||
| AN924-8S | .500 | AN924-8R | AS5178R08 | |
| AN924-8T | .500 | AS5178T08 | ||
| AN924-8W | .500 | AS5178W08 | ||
| AN924-10 | .625 | AS5178-10- | ||
| AN924-10D | .625 | AN924-10W | AS5178W10 | |
| AN924-10J | .625 | AS5178J10 | ||
| AN924-10K | .625 | AS5178K10 | ||
| AN924-10R | .625 | AS5178R10 | ||
| AN924-10S | .625 | AN924-10R | AS5178R10 | |
| AN924-10T | .625 | AS5178T10 | ||
| AN924-10W | .625 | AS5178W10 | ||
| AN924-12 | .750 | AS5178-12- | ||
| AN924-12D | .750 | AN924-12W | AS5178W12 | |
| AN924-12J | .750 | AS5178J12 | ||
| AN924-12K | .750 | AS5178K12 | ||
| AN924-12R | .750 | AS5178R12 | ||
| AN924-12S | .750 | AN924-12R | AS5178R12 | |
| AN924-12T | .750 | AS5178T12 | ||
| AN924-12W | .750 | AS5178W12 | ||
| AN924-16 | 1.000 | AS5178-16- | ||
| AN924-16D | 1.000 | AN924-16W | AS5178W16 | |
| AN924-16J | 1.000 | AS5178J16 | ||
| AN924-16K | 1.000 | AS5178K16 | ||
| AN924-16R | 1.000 | AS5178R16 | ||
| AN924-16S | 1.000 | AN924-16R | AS5178R16 | |
| AN924-16T | 1.000 | AS5178T16 | ||
| AN924-16W | 1.000 | AS5178W16 | ||
| AN924-20 | 1.250 | AS5178-20- | ||
| AN924-20D | 1.250 | AN924-20W | AS5178W20 | |
| AN924-20J | 1.250 | AS5178J20 | ||
| AN924-20K | 1.250 | AS5178K20 | ||
| AN924-20R | 1.250 | AS5178R20 | ||
| AN924-20S | 1.250 | AN924-20R | AS5178R20 | |
| AN924-20T | 1.250 | AS5178T20 | ||
| AN924-20W | 1.250 | AS5178W20 | ||
| AN924-24 | 1.500 | AS5178-24- | ||
| AN924-24D | 1.500 | AN924-24W | AS5178W24 | |
| AN924-24J | 1.500 | AS5178J24 | ||
| AN924-24K | 1.500 | AS5178K24 | ||
| AN924-24R | 1.500 | AS5178R24 | ||
| AN924-24S | 1.500 | AN924-24R | AS5178R24 | |
| AN924-24T | 1.500 | AS5178T24 | ||
| AN924-24W | 1.500 | AS5178W24 | ||
| AN924-28 | 1.750 | AS5178-28- | ||
| AN924-28D | 1.750 | AN924-28W | AS5178W28 | |
| AN924-28J | 1.750 | AS5178J28 | ||
| AN924-28K | 1.750 | AS5178K28 | ||
| AN924-28R | 1.750 | AS5178R28 | ||
| AN924-28S | 1.750 | AN924-28R | AS5178R28 | |
| AN924-28T | 1.750 | AS5178T28 | ||
| AN924-28W | 1.750 | AS5178W28 | ||
| AN924-32 | 2.000 | AS5178-32- | ||
| AN924-32D | 2.000 | AN924-32W | AS5178W32 | |
| AN924-32J | 2.000 | AS5178J32 | ||
| AN924-32K | 2.000 | AS5178K32 | ||
| AN924-32R | 2.000 | AS5178R32 | ||
| AN924-32S | 2.000 | AN924-32R | AS5178R32 | |
| AN924-32T | 2.000 | AS5178T32 | ||
| AN924-32W | 2.000 | AS5178W32 | ||
| AN924-40 | 2.500 | AS5178-40- | ||
| AN924-40D | 2.500 | AN924-40W | AS5178W40 | |
| AN924-40J | 2.500 | AS5178J40 | ||
| AN924-40K | 2.500 | AS5178K40 | ||
| AN924-40R | 2.500 | AS5178R40 | ||
| AN924-40S | 2.500 | AN924-40R | AS5178R40 | |
| AN924-40T | 2.500 | AS5178T40 | ||
| AN924-40W | 2.500 | AS5178W40 | ||
| AN924-48 | 3.000 | AS5178-48- | ||
| AN924-48D | 3.000 | AN924-48W | AS5178W48 | |
| AN924-48J | 3.000 | AS5178J48 | ||
| AN924-48K | 3.000 | AS5178K48 | ||
| AN924-48R | 3.000 | AS5178R48 | ||
| AN924-48S | 3.000 | AN924-48R | AS5178R48 | |
| AN924-48T | 3.000 | AS5178T48 | ||
| AN924-48W | 3.000 | AS5178W48 |
1/ For new design use material designator R and W.
2/ Hardness has to be specified in the contract or purchase order.
3/ SAE does not have plating finish designators for the following types: G, H, L, M, N, P, TF, Z, and ZN.
GENERAL GUIDANCE
Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes.