DETAIL SPECIFICATION SHEET
CROSS, PIPE
INCH-POUND · AN918 Rev 10 · 8 December 2020 · Superseding AN918 Rev 9, 19 July 2011 · AMSC N/A · FSC 4730
FIGURE 1. Cross dimensions and configurations.

FIGURE 1. Cross dimensions and configurations – Continued.
| Dash number |
A Pipe thread ANPT SAE-AS71051 |
B +.094 (2.39) -0.00 inches (mm) |
C inches (mm) |
K Dia. inches (mm) |
K tolerance |
|---|---|---|---|---|---|
| 1 | 1/8-27 | 1.281 (32.54) | .625 (15.88) | .327 (8.31) | +.000 -.016 (0.41) |
| 2 | 1/4-18 | 1.781 (45.24) | .813 (20.65) | .423 (10.74) | +.000 -.019 (0.48) |
| 3 | 3/8-18 | 1.938 (49.23) | .938 (23.83) | .557 (14.15) | +.000 -.028 (0.71) |
| 4 | 1/2-14 | 2.469 (62.71) | 1.188 (30.18) | .688 (17.48) | +.000 -.034 (0.86) |
| 6 | 3/4-14 | 2.688 (68.28) | 1.375 (34.93) | .897 (22.78) | +.000 -.040 (1.02) |
| 8 | 1-11 1/2 | 3.250 (82.55) | 1.750 (44.45) | 1.128 (28.65) | +.000 -.037 (0.94) |
| 10 | 1/ 1/4-11 1/2 | 3.375 (85.73) | 2.156 (54.76) | 1.471 (37.36) | +.000 -.036 (0.91) |
| Dash number |
P Dia. inches (mm) |
S Approx inches (mm) |
W Rad. inches (mm) |
|---|---|---|---|
| 1 | .578 (14.68) | .500 (12.70) | .063 (1.60) |
| 2 | .781 (19.84 ) | .625 (15.88) | .094 (2.39) |
| 3 | .922 (23.42) | .750 (19.05) | .094 (2.39) |
| 4 | 1.156 (29.36) | .875 (22.23) | .125 (3.18) |
| 6 | 1.359 (34.52) | 1.000 (25.40) | .125 (3.18) |
| 8 | 1.688 (42.88) | 1.125 (28.58) | .125 (3.18) |
| 10 | 2.094 (53.19) | 1.250 (31.75) | .156 (3.96) |
NOTES
- Dimensions are in inches.
- Metric equivalents are given for information only.
- Unless otherwise specified tolerances are ±.016 inch (0.41 mm).
- Break sharp edges .and remove all hanging burrs and slivers
- Machined surfaces shall be finished to 125µin Ra, forged surfaces shall be 250µin Ra, unless otherwise specified on the figures. Surface finish shall be in accordance with ASME B46.1.
- For design features purposes, this standard takes precedence over documents referenced herein.
- Referenced documents shall be of the issue in effect on date of invitation for bid.
REQUIREMENTS
Dimensions and configuration shall be in accordance with figure 1.
Materials and finishes shall be in accordance with SAE-AS4842, see table I for material code.
TABLE I. Material and code letters.
| Code letter | Material |
|---|---|
| Blank | Copper alloy |
| J | Corrosion resistant steel (CRES), type 304 |
| K | CRES, type 316 |
| R | CRES, type 321 |
| W | Aluminum alloy 7075-T73 |
1/ Not for use in oxygen systems.
Marking: Part shall be permanently marked with the AN PIN, and include the manufacturers CAGE, name, or trademark.
PART IDENTIFICATION NUMBER (PIN) SPECIFICATION
The PIN consists of the prefix “AN” the specification sheet number, a dash number for pipe size, and material code letter. Unassigned PIN’s shall not be used.
PIN example: AN918-4W indicates a cross, 1/2-14 ANPT internal pipe threads, aluminum alloy 7075-T73.
SUPERSESSION DATA
Due to stress corrosion cracking aluminum alloys 2014 and 2024 “D” designator has been replaced by aluminum alloy 7075 “W” designator. Example: AN918-8D use AN918-8W.
Metal cracking due to high temperatures CRES alloy 347 “S” designator has been replaced by CRES alloy 321 “R” designator. Example: AN918-8S use AN918-8R.
Table II provides a detailed cross-reference of cancelled AN918 PINs and replacement SAE-AS4858 PINs. Users are cautioned to evaluate replacements for their particular application.
CAUTION: The superseding information is valid as of the date of this specification and may be superseded by subsequent revisions of the superseding document.
TABLE II. Cross-reference data.
| AN PIN (inactive) |
Pipe size |
Replacement AS PIN (for new design) |
Replacement AN PIN (inactive) |
|---|---|---|---|
| AN918-1 | .125 | AS4858-01 | |
| AN918-1D | .125 | AS4858W01 | AN918-1W |
| AN918-1J | .125 | AS4858J01 | |
| AN918-1K | .125 | AS4858K01 | |
| AN918-1R | .125 | AS4858R01 | |
| AN918-1S | .125 | AS4858R01 | AN918-1R |
| AN918-1W | .125 | AS4858W01 | |
| AN918-2 | .250 | AS4858-02 | |
| AN918-2D | .250 | AS4858W02 | AN918-2W |
| AN918-2J | .250 | AS4858J02 | |
| AN918-2K | .250 | AS4858K02 | |
| AN918-2R | .250 | AS4858R02 | |
| AN918-2S | .250 | AS4858R02 | AN918-2R |
| AN918-2W | .250 | AS4858W02 | |
| AN918-3 | .375 | AS4858-03 | |
| AN918-3D | .375 | AS4858W03 | AN918-3W |
| AN918-3J | .375 | AS4858J03 | |
| AN918-3K | .375 | AS4858K03 | |
| AN918-3R | .375 | AS4858R03 | |
| AN918-3S | .375 | AS4858R03 | AN918-3R |
| AN918-3W | .375 | AS4858W03 | |
| AN918-4 | .500 | AS4858-04 | |
| AN918-4D | .500 | AS4858W04 | AN918-4W |
| AN918-4J | .500 | AS4858J04 | |
| AN918-4K | .500 | AS4858K04 | |
| AN918-4R | .500 | AS4858R04 | |
| AN918-4S | .500 | AS4858R04 | AN918-4R |
| AN918-4W | .500 | AS4858W04 | |
| AN918-6 | .750 | AS4858-06 | |
| AN918-6D | .750 | AS4858W06 | AN918-6W |
| AN918-6J | .750 | AS4858J06 | |
| AN918-6K | .750 | AS4858K06 | |
| AN918-6R | .750 | AS4858R06 | |
| AN918-6S | .750 | AS4858R06 | AN918-6R |
| AN918-6W | .750 | AS4858W06 | |
| AN918-8 | 1.000 | AS4858-08 | |
| AN918-8D | 1.000 | AS4858W08 | AN918-8W |
| AN918-8J | 1.000 | AS4858J08 | |
| AN918-8K | 1.000 | AS4858K08 | |
| AN918-8R | 1.000 | AS4858R08 | |
| AN918-8S | 1.000 | AS4858R08 | AN918-8R |
| AN918-8W | 1.000 | AS4858W08 | |
| AN918-10 | 1.250 | AS4858-10 | |
| AN918-10D | 1.250 | AS4858W10 | AN918-10W |
| AN918-10J | 1.250 | AS4858J10 | |
| AN918-10K | 1.250 | AS4858K10 | |
| AN918-10R | 1.250 | AS4858R10 | |
| AN918-10S | 1.250 | AS4858R10 | AN918-10R |
| AN918-10W | 1.250 | AS4858W10 |
GENERAL GUIDANCE
Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the previous issue.