DETAIL SPECIFICATION SHEET
ELBOW, PIPE, INTERNAL THREAD, 90°
INCH-POUND · AN916 Rev 11 · 19 July 2011 · Superseding AN916 Rev 10, 10 February 1984 · AMSC N/A · FSC 4730
FIGURE 1. Elbow 90° dimensions and configuration.

FIGURE 1. Elbow 90° dimensions and configuration – Continued.
| Dash number |
A Pipe thread ANPT SAE-AS71051 |
B +.046 (1.17) -0.00 inches (mm) |
C inches (mm) |
E +.046 (1.17) -0.00 inches (mm) |
|---|---|---|---|---|
| 1 | 1/8-27 | .641 (16.28 ) | .625 (15.88) | .641 (16.28) |
| 2 | 1/4-18 | .891 (22.63) | .813 (20.65) | .953 (24.21) |
| 3 | 3/8-18 | .969 (24.61) | .938 (23.83) | 1.094 (27.79 |
| 4 | 1/2-14 | 1.234 (31.34) | 1.188 (30.18) | 1.359 (34.52) |
| 6 | 3/4-14 | 1.344 (34.14) | 1.375 (34.93) | 1.469 (37.31) |
| 8 | 1-11 1/2 | 1.625 (41.28) | 1.750 (44.45) | 1.813 (46.05) |
| 10 | 1/ 1/4-11 1/2 | 1.688 (42.88) | 2.156 (54.76) | 1.875 (47.63) |
| Dash number |
K Dia. inches (mm) |
K tolerance |
P Dia. inches (mm) |
S Approx inches (mm) |
W Rad. inches (mm) |
|---|---|---|---|---|---|
| 1 | .327 (8.31) | +.000 -.016 (0.41) | .578 (14.68) | .500 (12.70) | .063 (1.60) |
| 2 | .423 (10.74) | +.000 -.019 (0.48) | .781 (19.84) | .625 (15.88) | .094 (2.39) |
| 3 | .557 (14.15) | +.000 -.028 (0.71) | .922 (23.42) | .750 (19.05) | .094 (2.39) |
| 4 | .688 (17.48) | +.000 -.034 (0.86) | 1.156 (29.36) | .875 (22.23) | .125 (3.18) |
| 6 | .897 (22.78) | +.000 -.040 (1.02) | 1.359 (34.52) | 1.000 (25.40) | .125 (3.18) |
| 8 | 1.128 (28.65) | +.000 -.037 (0.94) | 1.688 (42.88) | 1.125 (28.58) | .125 (3.18) |
| 10 | 1.471 (37.36) | +.000 -.036 (0.91) | 2.094 (53.19) | 1.250 (31.75) | .156 (3.96) |
NOTES
- Dimensions are in inches.
- Metric equivalents are given for information only.
- Unless otherwise specified tolerances are ±.015 inch (0.38 mm).
- Break sharp edges .and remove all hanging burrs and slivers
- Machined surfaces shall be finished to 125µin Ra, forged surfaces shall be 250µin Ra, unless otherwise specified on the figures. Surface finish shall be in accordance with ASME B46.1.
- For design features purposes, this standard takes precedence over documents referenced herein.
- Referenced documents shall be of the issue in effect on date of invitation for bid.
REQUIREMENTS
Dimensions and configuration shall be in accordance with figure 1.
Materials and finishes shall be in accordance with SAE-AS4842, see table I for material code.
TABLE I. Material and designators.
| Code letter | Material |
|---|---|
| Blank | Copper alloy |
| J | Corrosion resistant steel (CRES), type 304 |
| K | CRES, type 316Cannon |
| R | CRES. Type 321 |
| W | Aluminum alloy 7075-T73 |
Marking: Part shall be permanently marked with the AN PIN, and include the manufacturers CAGE, name, or trademark.
PART IDENTIFICATION NUMBER (PIN) SPECIFICATION
The PIN consists of the prefix “AN” the specification sheet number, a dash number for pipe size, and material code letter. Unassigned PIN’s shall not be used.
PIN example: AN916-4W indicates a 90° elbow, 1/2-14 ANPT internal pipe threads, aluminum alloy 7075-T73.
SUPERSESSION DATA
Due to stress corrosion cracking aluminum alloys 2014 and 2024 “D” designator has been replaced by aluminum alloy 7075 “W” designator. Example: AN916-8D use AN916-8W.
Metal cracking due to high temperatures CRES alloy 347 “S” designator has been replaced by CRES alloy 321 “R” designator. Example: AN918-6S use AN916-8R.
Table II provides a detailed cross-reference of AN916 PINs and replacement SAE-AS4856 PINs. Users are cautioned to evaluate replacements for their particular application.
CAUTION: The superseding information is valid as of the date of this specification and may be superseded by subsequent revisions of the superseding document.
TABLE II. Cross-reference data.
| AN PIN (inactive) |
Pipe size |
Replacement AS PIN (for new design) |
Replacement AN PIN (inactive) |
|---|---|---|---|
| AN916-1 | .125 | AS4856-01 | |
| AN916-1D | .125 | AS4856W01 | AN916-1W |
| AN916-1J | .125 | AS4856J01 | |
| AN916-1K | .125 | AS4856K01 | |
| AN916-1R | .125 | AS4856R01 | |
| AN916-1S | .125 | AS4856R01 | AN916-1R |
| AN916-1W | .125 | AS4856W01 | |
| AN916-2 | .250 | AS4856-02 | |
| AN916-2D | .250 | AS4856W02 | AN916-2W |
| AN916-2J | .250 | AS4856J02 | |
| AN916-2K | .250 | AS4856K02 | |
| AN916-2R | .250 | AS4856R02 | |
| AN916-2S | .250 | AS4856R02 | AN916-2R |
| AN916-2W | .250 | AS4856W02 | |
| AN916-3 | .375 | AS4856-03 | |
| AN916-3D | .375 | AS4856W03 | AN916-3W |
| AN916-3J | .375 | AS4856J03 | |
| AN916-3K | .375 | AS4856K03 | |
| AN916-3R | .375 | AS4856R03 | |
| AN916-3S | .375 | AS4856R03 | AN916-3R |
| AN916-3W | .375 | AS4856W03 | |
| AN916-4 | .500 | AS4856-04 | |
| AN916-4D | .500 | AS4856W04 | AN916-4W |
| AN916-4J | .500 | AS4856J04 | |
| AN916-4K | .500 | AS4856K04 | |
| AN916-4R | .500 | AS4856R04 | |
| AN916-4S | .500 | AS4856R04 | AN916-4R |
| AN916-4W | .500 | AS4856W04 | |
| AN916-6 | .750 | AS4856-06 | |
| AN916-6D | .750 | AS4856W06 | AN916-10W |
| AN916-6J | .750 | AS4856J06 | |
| AN916-6K | .750 | AS4856K06 | |
| AN916-6R | .750 | AS4856R06 | |
| AN916-6S | .750 | AS4856R06 | AN916-10R |
| AN916-6W | .750 | AS4856W06 | |
| AN916-10 | 1.000 | AS4856-08 | |
| AN916-8D | 1.000 | AS4856W08 | AN916-10W |
| AN916-8J | 1.000 | AS4856J08 | |
| AN916-8K | 1.000 | AS4856K08 | |
| AN916-8R | 1.000 | AS4856R08 | |
| AN916-8S | 1.000 | AS4856R08 | AN916-10R |
| AN916-8W | 1.000 | AS4856W08 | |
| AN916-10 | 1.250 | AS4856-10 | |
| AN916-10D | 1.250 | AS4856W10 | AN916-10W |
| AN916-10J | 1.250 | AS4856J10 | |
| AN916-10K | 1.250 | AS4856K10 | |
| AN916-10R | 1.250 | AS4856R10 | |
| AN916-10S | 1.250 | AS4856R10 | AN916-10R |
| AN916-10W | 1.250 | AS4856W10 |
GENERAL GUIDANCE
Changes from previous issues. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes.