DETAIL SPECIFICATION SHEET
NIPPLE, PIPE
INCH-POUND · AN911 Rev 10 · 19 July 2011 · Superseding AN911 Rev 9, 20 March 1979 · AMSC N/A · FSC 4730
FIGURE 1. Nipple pipe dimensions and configurations.

FIGURE 1. Nipple pipe dimensions and configurations – Continued.
| Dash number pipe size |
SAE-AS5201 size code |
A Pipe thread ANPT SAE-AS71051 |
B +.031 (0.79) inches (mm) |
C inches (mm) |
C tolerance |
|---|---|---|---|---|---|
| 1 | 02 | 1/8-27 | .969 (24.61) | .438 (11.130) | +.003 (0.08) -.004 (0.10) |
| 2 | 04 | 1/4-18 | 1.438 (36.52) | .625 (15.88) | ±.004 (0.10) |
| 3 | 06 | 3/8-18 | 1.469 (37.31) | .750 (19.05) | ±.004 (0.10) |
| 4 | 08 | 1/2-14 | 1.844 (46.84) | .938 (23.83) | ±.004 (0.10) |
| 6 | 12 | 3/4-14 | 1.906 (48.41) | 1.125 (28.58) | ±.005 (.013) |
| 8 | 16 | 1-11 1/2 | 2.313 (58.75) | 1.375 (34.93) | ±.005 (0.13) |
| 10 | 20 | 1/ 1/4-11 1/2 | 2.344 (59.54) | 1.750 (44.45) | ±.016 (0.41) |
| Dash number pipe size |
K Dia. inches (mm) |
K tolerance |
L inches (mm) |
|---|---|---|---|
| 1 | .203 (5.16) | +.003 (0.08) -.004 (0.10) | .391 (9.93) |
| 2 | .279 (7.09) | ±.004 (0.10) | .594 (15.09) |
| 3 | .418 (10.62) | +.006 (0.15) -.007 (0.18) | .594 (15.09) |
| 4 | .508 (12.90) | ±.010 (0.25) | .766 (19.46) |
| 6 | .727 (18.47) | +.009 (0.23) -.010 (0.25) | .781 (19.84) |
| 8 | .914 (23.22) | ±.010 (0.25) | .969 (24.61) |
| 10 | 1.256 (31.90) | ±.008 (0.20) | .984 (24.99) |
| Dash number pipe size |
Weight max lbs (kg) Copper alloy |
Weight max lbs (kg) Al alloy |
Weight max lbs (kg) Steel, CRES |
Weight max lbs (kg) Ti alloy |
|---|---|---|---|---|
| 1 | .027 (0.01) | .009 (0.004) | .027 (0.012) | .015 (0.007) |
| 2 | .072 (0.03) | .024 (0.010) | .072 (0.033) | .040 (0.018) |
| 3 | .093 (0.04) | .031 (0.014) | .093 (0.042) | .051 (0.023) |
| 4 | .186 (0.08) | .062 (0.028) | .186 (0.084) | .102 (0.046) |
| 6 | .249 (0.11) | .083 (0.038) | .240 (0.109) | .137 (0.062) |
| 8 | .444 (0.20) | .148 (0.067) | .443 (0.196) | .245 (0.111) |
| 10 | .606 (0.27) | .202 (0.091) | .605 (0.274) | .334 (0.151) |
NOTES
- Dimensions are in inches.
- Metric equivalents are given for information only.
- Break sharp edges .and remove all hanging burrs and slivers
- Machined surfaces shall be finished to 125µin Ra, forged surfaces shall be 250µin RA, unless otherwise specified on the figures. Surface finish shall be in accordance with ASME B46.1.
- For design features purposes, this standard takes precedence over documents referenced herein.
- Referenced documents shall be of the issue in effect on date of invitation for bid.
REQUIREMENTS
Dimensions and configuration shall be in accordance with figure 1.
Materials and finishes shall be in accordance with SAE-AS4842, see table I for material code.
TABLE I. Material and code letters.
| Code letter | Material |
|---|---|
| Blank | Copper alloy |
| J | Corrosion resistant steel (CRES), type 304 |
| K | CRES, type 316 |
| R | CRES. Type 321 |
| T | Titanium alloy 1/ |
| W | Aluminum alloy 7075-T73 |
1/ Not for use in oxygen systems.
Marking: Part shall be permanently marked with the AN PIN, and include the manufacturers CAGE, name, or trademark.
PART IDENTIFICATION NUMBER (PIN) SPECIFICATION
The PIN consists of prefix “AN” the specification sheet number, a dash number for pipe size, and material code letter. Unassigned PIN’s shall not be used.
PIN example: AN911-4W indicates a pipe nipple, .500 inch (12.70 mm), aluminum alloy 7075-T73.
SUPERSESSION DATA
Due to stress corrosion cracking aluminum alloys 2014 and 2024 “D” designator has been replaced by aluminum alloy 7075 “W” designator. Example: AN911-8D use AN911-8W.
Metal cracking due to high temperatures CRES alloy 347 “S” designator has been replaced by CRES alloy 321 “R” designator. Example: AN911-8S use AN911-8R.
Table II provides a detailed cross-reference of cancelled AN911 PINs and replacement SAE-AS4860 PINs. Users are cautioned to evaluate replacements for their particular application.
CAUTION: The superseding information is valid as of the date of this specification and may be superseded by subsequent revisions of the superseding document.
TABLE II. Cross-reference data.
| AN PIN (inactive) |
Pipe size |
Replacement AS PIN (for new design) |
Replacement AN PIN (inactive) |
|---|---|---|---|
| AN911-1 | .125 | AS4860-01 | |
| AN911-1D | .125 | AS4860W01 | AN911-1W |
| AN911-1J | .125 | AS4860J01 | |
| AN911-1K | .125 | AS4860K01 | |
| AN911-1R | .125 | AS4860R01 | |
| AN911-1S | .125 | AS4860R01 | AN911-1R |
| AN911-1T | .125 | None | |
| AN911-1W | .125 | AS4860W01 | |
| AN911-2 | .250 | AS4860-02 | |
| AN911-2D | .250 | AS4860W02 | AN911-2W |
| AN911-2J | .250 | AS4860J02 | |
| AN911-2K | .250 | AS4860K02 | |
| AN911-2R | .250 | AS4860R02 | |
| AN911-2S | .250 | AS4860R02 | AN911-2R |
| AN911-2T | .250 | None | |
| AN911-2W | .250 | AS4860W02 | |
| AN911-3 | .375 | AS4860-03 | |
| AN911-3D | .375 | AS4860W03 | AN911-3W |
| AN911-3J | .375 | AS4860J03 | |
| AN911-3K | .375 | AS4860K03 | |
| AN911-3R | .375 | AS4860R03 | |
| AN911-3S | .375 | AS4860R03 | AN911-3R |
| AN911-3T | .375 | None | |
| AN911-3W | .375 | AS4860W03 | |
| AN911-4 | .500 | AS4860-04 | |
| AN911-4D | .500 | AS4860W04 | AN911-4W |
| AN911-4J | .500 | AS4860J04 | |
| AN911-4K | .500 | AS4860K04 | |
| AN911-4R | .500 | AS4860R04 | |
| AN911-4S | .500 | AS4860R04 | AN911-4R |
| AN911-4T | .500 | None | |
| AN911-4W | .500 | AS4860W04 | |
| AN911-6 | .750 | AS4860-06 | |
| AN911-6D | .750 | AS4860W06 | AN911-6W |
| AN911-6J | .750 | AS4860J06 | |
| AN911-6K | .750 | AS4860K06 | |
| AN911-6R | .750 | AS4860R06 | |
| AN911-6S | .750 | AS4860R06 | AN911-6R |
| AN911-6T | .750 | None | |
| AN911-6W | .750 | AS4860W06 | |
| AN911-8 | 1.000 | AS4860-08 | |
| AN911-8D | 1.000 | AS4860W08 | AN911-8W |
| AN911-8J | 1.000 | AS4860J08 | |
| AN911-8K | 1.000 | AS4860K08 | |
| AN911-8R | 1.000 | AS4860R08 | |
| AN911-8S | 1.000 | AS4860R08 | AN911-8R |
| AN911-8T | 1.000 | None | |
| AN911-8W | 1.000 | AS4860W08 | |
| AN911-10 | 1.250 | AS4860-10 | |
| AN911-10D | 1.250 | AS4860W10 | AN911-10 |
| AN911-10J | 1.250 | AS4860J10 | |
| AN911-10K | 1.250 | AS4860K10 | |
| AN911-10R | 1.250 | AS4860R10 | |
| AN911-10S | 1.250 | AS4860R10 | AN911-10R |
| AN911-10T | 1.250 | None | |
| AN911-10W | 1.250 | AS4860W10 |
GENERAL GUIDANCE
Changes from previous issues. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes.