DETAIL SPECIFICATION SHEET
COUPLING, PIPE
INCH-POUND · AN910 Rev 12 · 30 November 2021 · Superseding AN910 Rev 11, 7 June 2011 · AMSC N/A · FSC 4730
FIGURE 1. Coupling pipe dimensions and configuration.

FIGURE 1. Coupling pipe dimensions and configuration – Continued.
| Dash number |
A Pipe thread SAE-AS71051 |
B +.031 (0.79) inches (mm) |
C inches (mm) |
C tolerance |
K Diameter inches (mm) |
K tolerance |
|---|---|---|---|---|---|---|
| 1 | 1/8-27 ANPT | .844 (21.44) | .625 (15.88) | ±.004 (0.10) | .327 (8.31) | +.000 -.016 (0.41) |
| 2 | 1/4-18 ANPT | 1.125 (28.58) | .813 (20.65) | ±.004 (0.10) | .423 (10.74) | +.000 -.019 (0.48) |
| 3 | 3/8-18 ANPT | 1.219 (30.96) | .938 (23.83) | ±.004 (0.10) | .557 (14.15) | +.000 -.028 (0.71) |
| 4 | 1/2-14 ANPT | 1.594 (40.89) | 1.188 (30.18) | ±.005 (0.13) | .688 (17.48) | +.000 -.034 (0.86) |
| 6 | 3/4-14 ANPT | 1.625 (41.28) | 1.375 (34.93) | ±.005 (.013) | .897 (22.78) | +.000 -.040 (1.02) |
| 8 | 1-11.5 ANPT | 1.938 (49.23) | 1.750 (44.45) | ±.016 (0.41) | 1.128 (28.65) | +.000 -.037 (0.94) |
| 10 | 1/ 1/4-11.5 ANPT | 1.938 (49.23) | 2.125 (53.98) | ±.020 (0.51) | 1.471 (37.36) | +.000 -.036 (0.91) |
| Dash number |
P Diameter ±.016 (0.41) inches (mm) |
Z ±.016 (0.41) inches (mm) |
|---|---|---|
| 1 | .578 (14.68) | .313 (7.95) |
| 2 | .781 (19.84) | .438 (11.13) |
| 3 | .922 (23.42) | .469 (11.91) |
| 4 | 1.156 (29.36) | .641 (16.28) |
| 6 | 1.359 (34.52) | .641 (16.28) |
| 8 | 1.688 (42.88) | .781 (19.84) |
| 10 | 1.094 (27.79) | .781 (19.84) |
NOTES
- Dimensions are in inches.
- Metric equivalents are given for information only.
- Break sharp edges and remove all hanging burrs and slivers.
- Machined surfaces shall be finished to 125µ in Ra, forged surfaces shall be 250µ inches Ra, unless otherwise specified on the figures. Surface finish shall be in accordance with ASME B46.1.
- For design features purposes, this standard takes precedence over documents referenced herein.
- Referenced documents shall be of the issue in effect on date of invitation for bid.
REQUIREMENTS
Dimensions and configuration. The coupling pipe dimensions and configuration shall be in accordance with figure 1 and table I.
Materials and finishes shall be in accordance with SAE-AS4842, see table I for material code letters.
TABLE I. Material and code letters.
| Code letter | Material |
|---|---|
| Blank | Copper alloy |
| J | Corrosion resistant steel (CRES), type 304 |
| K | CRES, type 316 |
| R | CRES. Type 321 |
| S | CRES, type 347 |
| W | Aluminum alloy 7075-T73 |
Marking: Part shall be permanently marked with the AN PIN, and include the manufacturers CAGE, name, or trademark.
PART IDENTIFICATION NUMBER (PIN) SPECIFICATION
The PIN consists of the letter “AN” the specification sheet number, a dash number for pipe thread size, and a material code letter for material type. Unassigned PINs shall not be used.
PIN example: AN910-4W indicates a coupling pipe, .500 inch (12.70 mm) ID, aluminum alloy 7075-T73.
SUPERSESSION DATA
The aluminum “D” designator has been replaced by the “W” designator.
Table II provides a detailed cross-reference of AN910 PINs and replacement SAE-AS4859 PINs. Users are cautioned to evaluate replacements for their particular application.
CAUTION: The superseding information is valid as of the date of this specification and may be superseded by subsequent revisions of the superseding document.
TABLE II. Cross-reference data. 1/
| AN PIN | Pipe Thread |
Replacement AS PIN |
New design |
|---|---|---|---|
| AN910-1 | .125 | AS4859-01 | |
| AN910-1D | .125 | AS4859W01 | AS4859W01 |
| AN910-1J | .125 | AS4859J01 | |
| AN910-1K | .125 | AS4859K01 | |
| AN910-1R | .125 | AS4859R01 | |
| AN910-1S | .125 | AS4859R01 | AS4859R01 |
| AN910-1W | .125 | AS4859W01 | |
| AN910-2 | .250 | AS4859-02 | |
| AN910-2D | .250 | AS4859W02 | AS4859W02 |
| AN910-2J | .250 | AS4859J02 | |
| AN910-2K | .250 | AS4859K02 | |
| AN910-2R | .250 | AS4859R02 | |
| AN910-2S | .250 | AS4859R02 | AS4859R02 |
| AN910-2W | .250 | AS4859W02 | |
| AN910-3 | .375 | AS4859-03 | |
| AN910-3D | .375 | AS4859W03 | AS4859W03 |
| AN910-3J | .375 | AS4859J03 | |
| AN910-3K | .375 | AS4859K03 | |
| AN910-3R | .375 | AS4859R03 | |
| AN910-3S | .375 | AS4859R03 | AS4859R03 |
| AN910-3W | .375 | AS4859W03 | |
| AN910-4 | .500 | AS4859-04 | |
| AN910-4D | .500 | AS4859W04 | AS4859W04 |
| AN910-4J | .500 | AS4859J04 | |
| AN910-4K | .500 | AS4859K04 | |
| AN910-4R | .500 | AS4859R04 | |
| AN910-4S | .500 | AS4859R04 | AS4859R04 |
| AN910-4W | .500 | AS4859W04 | |
| AN910-6 | .750 | AS4859-06 | |
| AN910-6D | .750 | AS4859W06 | AS4859W06 |
| AN910-6J | .750 | AS4859J06 | |
| AN910-6K | .750 | AS4859K06 | |
| AN910-6R | .750 | AS4859R06 | |
| AN910-6S | .750 | AS4859R06 | AS4859R06 |
| AN910-6W | .750 | AS4859W06 | |
| AN910-8 | 1.000 | AS4859-08 | |
| AN910-8D | 1.000 | AS4859W08 | AS4859W08 |
| AN910-8J | 1.000 | AS4859J08 | |
| AN910-8K | 1.000 | AS4859K08 | |
| AN910-8R | 1.000 | AS4859R08 | |
| AN910-8S | 1.000 | AS4859R08 | AS4859R08 |
| AN910-8W | 1.000 | AS4859W08 | |
| AN910-10 | 1.250 | AS4859-10 | |
| AN910-10D | 1.250 | AS4859W10 | AS4859W10 |
| AN910-10J | 1.250 | AS4859J10 | |
| AN910-10K | 1.250 | AS4859K10 | |
| AN910-10R | 1.250 | AS4859R10 | |
| AN910-10S | 1.250 | AS4859R10 | AS4859R10 |
| AN910-10W | 1.250 | AS4859W10 |
1/ For new design use material designator R and W.
GENERAL GUIDANCE
Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the previous issue.