DETAIL SPECIFICATION SHEET
NIPPLE, HOSE
INCH-POUND · AN849 Rev 13 w/Amendment 1 · 1 April 2025 · Superseding AN849 Rev 13, 10 March 2015 · AMSC N/A · FSC 4730
FIGURE 1. Nipple dimensions and configuration.

FIGURE 1. Nipple dimensions and configuration – Continued.
| Dash number |
Hose ID inches (mm) |
A inches (mm) |
B inches (mm) |
Thread C Ref SAE-AS8879 |
M inches (mm) |
|---|---|---|---|---|---|
| 4 | .250 (6.35) | 1.938 (49.23) | .438 (11.13) | .4375-20UNJF-3A | 3.625 (92.08) |
| 6 | .375 (9.53) | 1.969 (50.01) | .469 (11.91) | .5625-18UNJF-3A | 3.719 (94.46) |
| 8 | .500 (12.70) | 2.000 (50.80) | .500 (12.70) | .7500-16UNJF-3A | 3.781 (96.04) |
| 10 | .675 (17.15) | 2.031 (51.59) | .531 (13.49) | 1.875 -12UNJ-3A | 3.844 (97.64) |
| 12 | .750 (19.05) | 2.063 (52.40) | .563 (14.30) | 1.0625 -12UNJ-3A | 3.906 (99.21) |
| 16 | 1.000 (25.40) | 2.063 (52.40) | .563 (14.30) | 1.3125-12UNJ-3A | 3.906 (99.21) |
| 20 | 1.250 (31.75) | 2.063 (52.40) | .563 (14.30) | 1.6250-12UNJ-3A | 3.938 (100.03) |
| 24 | 1.500 (38.10) | 2.063 (52.40) | .563 (14.30) | 1.8750-12UNJ-3A | 4.000 (101.60) |
| Dash number |
S inches (mm) |
S tolerance |
|---|---|---|
| 4 | .688 (17.48) | ±.004 (0.10) |
| 6 | .813 (20.65) | |
| 8 | 1.000 (25.40) | |
| 10 | 1.125 (28.58) | ±.005 (0.13) |
| 12 | 1.375 (34.93) | |
| 16 | 1.625 (41.28) | ±.016 (0.41) |
| 20 | 1.875 (47.63) | |
| 24 | 2.125 (53.98) | ±.020 (0.51) |
NOTES
- Dimensions are in inches.
- Metric equivalents are given for information only.
- Unless otherwise specified tolerances are ±.016 inch (0.41 mm).
- Break sharp edges and remove all hanging burrs and slivers.
- Machined surfaces shall be finished to 125µ-in Ra, forged surfaces shall be 250µ-in Ra, unless otherwise specified on the figures. Surface finish shall be in accordance with ASME B46.1.
- For design features purposes, this standard takes precedence over documents referenced herein.
- Referenced documents shall be of the issue in effect on date of invitation for bid.
REQUIREMENTS
Dimensions and configuration shall be in accordance with figure 1.
Materials and finishes shall be in accordance with SAE-AS4843, see table I for material code.
TABLE I. Material and finish code letters.
| Material and finish code |
Material | Protective chemical finish 3/ 4/ |
|---|---|---|
| No code 1/ | Copper alloy, type 377 forging in accordance with ASTM B124/B124M or half hard forging or bar in accordance with ASTM B138/B138M or bar in accordance with SAE-AMS4614. | No finish. |
| BC 1/ 4/ | Copper alloy, type 377 forging in accordance with ASTM B124/B124M or half hard forging or bar in accordance with ASTM B138/B138M or bar in accordance with SAE-AMS4614. | Cadmium in accordance with SAE-AMS-QQ-P-416, type II, class 3. |
| D 2/ | Aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 alloy 2014-T6. Aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6 alloy 2024-T6, or aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6 or SAE-AMS4339 alloy 2024-T851. | Anodize in accordance with SAE-AMS2472 or MIL-PRF-8625, type II, class 2, dye blue, duplex seal in accordance with procurement specification. |
| DV 2/ | Aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 alloy 2014-T6. Aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6 alloy 2024-T6, or aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6 or SAE-AMS4339 alloy 2024-T851. | High purity aluminum in accordance with MIL-DTL-83488, class 3, type II with maximum coating thickness of .0005 inch. Glass bead peen pressure shall be 25 psi (1.72 bar) maximum. |
| J | Type 304 corrosion resistant steel (CRES) forging or bar in accordance with SAE-AMS-QQ-S-763 or SAE-AMS5639. | Passivate in accordance with SAE-AMS2700, method 1, type 6 or 7. |
| K | Type 316 corrosion resistant steel (CRES) forging or bar in accordance with SAE-AMS-QQ-S-763 or SAE-AMS5648. | Passivate in accordance with SAE-AMS2700, method 1, type 6 or 7. |
| R | Type 321 corrosion resistant steel (CRES) forging or bar in accordance with SAE-AMS-QQ-S-763 or SAE-AMS5645. | Passivate in accordance with SAE-AMS2700, method 1, type 6 or 7. |
| S 3/ | Type 347 corrosion resistant steel (CRES) forging or bar in accordance with SAE-QQ-S-763 or SAE-AMS5646 | Passivate in accordance with SAE-AMS2700, method 1, type 6 or 7. |
| T 4/ | Titanium in accordance with SAE-AMS4928 alloy 6AI-4V annealed. | Anodize in accordance with SAE-AMS2488, type 2. 5/ |
| TF 4/ | Titanium in accordance with SAE-AMS4928 alloy 6AI-4V annealed. | Fluoride phosphate in accordance with SAE-AMS2486. 5/ |
| W 2/ | Aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 alloy 7075-T73 or aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/9 or SAE-AMS4124, alloy 7075-T7351 or 7075-T73. | Anodize in accordance with SAE-AMS2472 or MIL-PRF-8625, type II, class 2, dye brown similar to color 10080 in accordance with SAE-AMS-STD-595, duplex seal in accordance with procurement specification. |
| WV 2/ | Aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 alloy 7075-T73 or aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/9 or SAE-AMS4124, alloy 7075-T7351 or 7075-T73. | High purity aluminum in accordance with MIL-DTL-83488, class 3, type II with maximum coating thickness of .0005 inch. Glass bead peen pressure shall be 25 psi (1.72 bar) maximum. |
1/ Material code was dash on revision 11, changed to agree with SAE-ARP1590.
2/ Aluminum code D is inactive for new design, use code W.
3/ CRES 347 code S is inactive for new design, use code R.
4/ Titanium and cadmium shall not be used in potable water or oxygen systems.
5/ A pretreatment, a modification of the fluoride treatment, or a post treatment shall be applied so the final color of the fittings shall be similar to SAE-AMS-STD-595 colors 36076 through 36293.
Marking: Part shall be permanently marked with the AN PIN, and include the manufacturers CAGE, name, or trademark.
Guidance on use of alternative parts with less hazardous or non-hazardous materials. This specification provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application.
Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.
Referenced documents shall be of the issue in effect on date of invitations for bid.
PART IDENTIFICATION NUMBER (PIN) SPECIFICATION
The PIN consists of the prefix “AN”, specification sheet number, dash number for hose and flared tube size, material finish code letter(s) and blank of “A” for oxygen cleaning requirements. Unassigned PIN’s shall not be used.
PIN examples: AN849-8W indicates a straight nipple .500 inch (.12.70 mm), aluminum alloy 7075-T73.
AN849-8WV indicates a straight nipple .500 inch (.12.70 mm), aluminum alloy 7075-T73 finish with high purity aluminum.
AN849-8WA indicates a straight nipple .500 inch (.12.70 mm), aluminum alloy 7075-T73 for use on oxygen systems.
SUPERSESSION DATA
Due to stress corrosion cracking aluminum alloys 2014 and 2024, “D” designator has been replaced by aluminum alloy 7075 “W” designator. Example: AN849-8D use AN849-8W.
Metal cracking due to high temperatures CRES alloy 347 “S” designator has been replaced by CRES alloy 321 “R” designator. Example: AN849-8S use AN849-8R.
Inactive AN PIN and superseding AN PIN see table II.
TABLE II. Superseding AN PIN.
| Inactive AN PIN |
Hose Size |
Superseding AN PIN Inactive part |
|---|---|---|
| AN849-4 | 0.250 | AN849-4B |
| AN849-4 | 0.250 | AN849-4BC |
| AN849-4D | 0.250 | AN849-4W |
| AN849-4DV | 0.250 | AN849-4WV |
| AN849-4S | 0.250 | AN849-4R |
| AN849-6 | 0.375 | AN849-6B |
| AN849-6 | 0.375 | AN849-6BC |
| AN849-6D | 0.375 | AN849-6W |
| AN849-6DV | 0.375 | AN849-6WV |
| AN849-6S | 0.375 | AN849-6R |
| AN849-8 | 0.500 | AN849-8B |
| AN849-8 | 0.500 | AN849-8BC |
| AN849-8D | 0.500 | AN849-8W |
| AN849-8DV | 0.500 | AN849-8WV |
| AN849-8S | 0.500 | AN849-8R |
| AN849-10 | 0.625 | AN849-10B |
| AN849-10 | 0.625 | AN849-10BC |
| AN849-10D | 0.625 | AN849-10W |
| AN849-10DV | 0.625 | AN849-10WV |
| AN849-10DV | 0.625 | AN849-10WV |
| AN849-10S | 0.625 | AN849-10R |
| AN849-12 | 0.750 | AN849-12B |
| AN849-12 | 0.750 | AN849-12BC |
| AN849-12D | 0.750 | AN849-12W |
| AN849-12DV | 0.750 | AN849-12WV |
| AN849-12R | 0.750 | AN849-12S |
| AN849-16 | 1.000 | AN849-16B |
| AN849-16 | 1.000 | AN849-16BC |
| AN849-16D | 1.000 | AN849-16W |
| AN849-16DV | 1.000 | AN849-16WV |
| AN849-16S | 1.000 | AN849-16R |
| AN849-20 | 1.250 | AN849-20B |
| AN849-20 | 1.250 | AN849-20BC |
| AN849-20D | 1.250 | AN849-20W |
| AN849-20DV | 1.250 | AN849-20WV |
| AN849-20S | 1.250 | AN849-20R |
| AN849-24 | 1.500 | AN849-24B |
| AN849-24 | 1.500 | AN849-24BC |
| AN849-24D | 1.500 | AN849-24W |
| AN849-24DV | 1.500 | AN849-24WV |
| AN849-24S | 1.500 | AN849-24R |
Cross reference data: SAE- AS5189 replacement numbers may be substituted for AN849 PINs, see table III.
Users are cautioned to evaluate replacements for their particular application.
CAUTION: The superseding information is valid as of the date of this specification and may be superseded by subsequent revisions of the superseding document.
TABLE III. Cross-reference data. 1/
| AN PIN Inactive for new design |
Hose Size |
Replacement AS PIN |
New design |
|---|---|---|---|
| AN849-4 | 0.250 | AS5189B04 2/ | |
| AN849-4D | 0.250 | AS5189W04 | AS5189W04 |
| AN849-4DV | 0.250 | None | |
| AN849-4J | 0.250 | AS5189J04 | |
| AN849-4K | 0.250 | AS5189K04 | |
| AN849-4R | 0.250 | AS5189R04 | |
| AN849-4S | 0.250 | AS5189R04 | AS5189R04 |
| AN849-4T | 0.250 | None | |
| AN849-4TF | 0.250 | None | |
| AN849-4W | 0.250 | AS5189W04 | |
| AN849-4WV | 0.250 | None | |
| AN849-6 | 0.375 | AS5189B06 2/ | |
| AN849-6D | 0.375 | AS5189W06 | AS5189W06 |
| AN849-6DV | 0.375 | None | |
| AN849-4J | 0.375 | AS5189J06 | |
| AN849-4K | 0.375 | AS5189K06 | |
| AN849-6R | 0.375 | AS5189R06 | |
| AN849-6S | 0.375 | AS5189R06 | AS5189R06 |
| AN849-4T | 0.375 | None | |
| AN849-4TF | 0.375 | None | |
| AN849-6W | 0.375 | AS5189W06 | |
| AN849-6WV | 0.375 | None | |
| AN849-8 | 0.500 | AS5189B08 | |
| AN849-8D | 0.500 | AS5189W08 | AS5189W08 |
| AN849-8DV | 0.500 | None | |
| AN849-8J | 0.500 | AS5189J08 | |
| AN849-8K | 0.500 | AS5189K08 | |
| AN849-8R | 0.500 | AS5189R08 | |
| AN849-8S | 0.500 | AS5189R08 | AS5189R08 |
| AN849-8T | 0.500 | None | |
| AN849-8TF | 0.500 | None | |
| AN849-8W | 0.500 | AS5189W08 | |
| AN849-8WV | 0.500 | None | |
| AN849-10 | 0.625 | AS5189B10 2/ | |
| AN849-10D | 0.625 | AS5189W10 | AS5189W10 |
| AN849-10DV | 0.625 | None | |
| AN849-10J | 0.625 | AS5189J10 | |
| AN849-10K | 0.625 | AS5189K10 | |
| AN849-10R | 0.625 | AS5189R10 | |
| AN849-10S | 0.625 | AS5189R10 | AS5189R10 |
| AN849-10T | 0.625 | None | |
| AN849-10TF | 0.625 | None | |
| AN849-10W | 0.625 | AS5189W10 | |
| AN849-10WV | 0.625 | None | |
| AN849-12 | 0.750 | AS5189B12 2/ | |
| AN849-12D | 0.750 | AS5189W12 | AS5189W12 |
| AN849-12DV | 0.750 | None | |
| AN849-12J | 0.750 | AS5189J12 | |
| AN849-12K | 0.750 | AS5189K12 | |
| AN849-12R | 0.750 | AS5189R12 | |
| AN849-12S | 0.750 | AS5189R12 | AS5189R12 |
| AN849-12T | 0.750 | None | |
| AN849-12TF | 0.750 | None | |
| AN849-12W | 0.750 | AS5189W12 | |
| AN849-12WV | 0.750 | None | |
| AN849-16 | 1.000 | AN5189B16 2/ | |
| AN849-16DV | 1.000 | AS5189W16 | AS5189W16 |
| AN849-16D | 1.000 | None | |
| AN849-16J | 1.000 | AS5189J16 | |
| AN849-16K | 1.000 | AS5189K16 | |
| AN849-16R | 1.000 | AS5189R16 | |
| AN849-16S | 1.000 | AS5189R16 | AS5189R16 |
| AN849-16T | 1.000 | None | |
| AN849-16TF | 1.000 | None | |
| AN849-16W | 1.000 | AS5189W16 | |
| AN849-16WV | 1.000 | None | |
| AN849-20 | 1.250 | AS5189B20 2/ | |
| AN849-20D | 1.250 | AS5189W20 | AS5189W20 |
| AN849-20DV | 1.250 | None | |
| AN849-20J | 1.250 | AS5189J20 | |
| AN849-20K | 1.250 | AS5189K20 | |
| AN849-20R | 1.250 | AS5189R20 | |
| AN849-20S | 1.250 | AS5189R20 | AS5189R20 |
| AN849-20T | 1.250 | None | |
| AN849-20TA | 1.250 | None | |
| AN849-20W | 1.250 | AS5189W20 | |
| AN849-20WV | 1.250 | None | |
| AN849-24 | 1.500 | AS5189B24 2/ | |
| AN849-24D | 1.500 | AS5189W24 | AS5189W24 |
| AN849-24DV | 1.500 | None | |
| AN849-24J | 1.500 | AS5189J24 | |
| AN849-24K | 1.500 | AS5189K24 | |
| AN849-24R | 1.500 | AS5189R24 | |
| AN849-24S | 1.500 | AS5189R24 | AS5189R24 |
| AN849-24T | 1.500 | None | |
| AN849-24TF | 1.500 | None | |
| AN849-24W | 1.500 | AS5189W24 |
1/ For new design use material designator R and W.
2/ SAE part may be unplated or cadmium plated.
GENERAL GUIDANCE
Amendment notations. The margins of this specification are marked with vertical lines to indicate modifications generated by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations.