DETAIL SPECIFICATION SHEET
ELBOW – PIPE TO HOSE, 45 DEGREE
INCH-POUND · AN844 Rev 14 · 12 March 2020 · Superseding AN844 Rev 13, 3 October 2013 · AMSC N/A · FSC 4730
FIGURE 1. 45° elbow dimensions and configuration.

FIGURE 1. 45° elbow dimensions and configuration – Continued.
| Dash number |
Hose ID inches (mm) |
A Pipe thread SAE-AS71051 |
B +.047 (1.19) -.000 inches (mm) |
C inches (mm) |
|---|---|---|---|---|
| 4 | .250 (6.35) | 1/8-27 ANPT | .625 (15.88) | .438 (11.13) |
| 6 | .375 (9.53) | 1/4-18 ANPT | .875 (22.23) | .625 (15.88) |
| 8 | .500 (12.70) | 3/8-18 ANPT | .922 (23.42) | .750 (19.05) |
| 10 | .625 (15.88) | 1/2-14 ANPT | 1.156 (29.36) | .938 (23.83) |
| 12 | .750 (19.05) | 3/4-14 ANPT | 1.203 (30.56) | 1.125 (28.58) |
| 16 | 1.000 (25.40) | 3/4-14 ANPT | 1.203 (30.56) | 1.125 (28.58) |
| 17 | 1.000 (25.40) | 1-11.5 ANPT | 1.484 (37.69) | 1.375 (34.93) |
| 20 | 1.250 (31.75) | 1/ 1/4-11.5 ANPT | 1.500 (38.10) | 1.750 (44.45) |
| 21 | 1.250 (31.75) | 1 -11.5 ANPT | 1.484 (37.69) | 1.375 (34.93) |
| 24 | 1.500 (38.10) | 1 1/2-11.5 ANPT | 1.563 (39.70) | 2.000 (50.80) |
| 25 | 1.500 (38.10) | 1 1/4-11.5 ANPT | 1.438 (37.67) | 1.750 (44.45) |
| Dash number |
J dia. inches (mm) |
M +.047 (1.19) -.000 inches (mm) |
S approx inches (mm) |
U approx inches (mm) |
|---|---|---|---|---|
| 4 | .438 (11.13) | 1.625 (41.28) | .313 (7.95) | .219 (5.56) |
| 6 | .578 (14.68) | 1.688 (42.88) | .375 (9.53) | .281 (7.14) |
| 8 | .719 (18.26) | 1.719 (43.66) | .500 (12.70) | .313 (7.95) |
| 10 | .891 (22.63) | 1.781 (45.24) | .625 (15.88) | .375 (9.53) |
| 12 | 1.094 (48.36) | 1.813 (46.05) | .625 (15.88) | .438 (11.13) |
| 16 | 1.094 (48.36) | 1.813 (46.05) | .625 (15.88) | .438 (11.13) |
| 17 | 1.375 (34.93) | 1.875 (47.63) | .750 (19.05) | .563 (14.30) |
| 20 | 1.719 (43.66) | 1.938 (49.23) | .938 (23.83) | .563 (14.30) |
| 21 | 1.375 (34.93) | 1.875 (47.63) | .750 (19.05) | .563 (14.30) |
| 24 | 1.953 (49.61) | 2.000 (50.80) | 1.125 (28.58) | .625 (15.88) |
| 25 | 1.719 (43.66) | 2.000 (50.80) | 1.125 (28.58) | .625 (15.88) |
| Dash number |
V radius. inches (mm) |
W radius inches (mm) |
X +.047 (1.19) -.000 inches (mm) |
Y +.047 (1.19) -.000 inches (mm) |
|---|---|---|---|---|
| 4 | .219 (5.56) | .063 (1.60) | 1.672 (42.47) | .656 (16.66) |
| 6 | .282 (7.16) | .063 (1.60) | 1.750 (44.45) | .938 (23.83) |
| 8 | .359 (9.12) | .094 (2.39) | 1.797 (45.64) | 1.000 (25.40) |
| 10 | .438 (11.13) | .094 (2.39) | 1.890 (48.10) | 1.266 (32.16) |
| 12 | .547 (13.89) | .125 (3.18) | 1.938 (49.23) | 1.359 (34.52) |
| 16 | .547 (13.89) | .125 (3.18) | 2.000 (50.80) | 1.359 (34.52) |
| 17 | .688 (17.48) | .125 (3.18) | 2.063 (52.40) | 1.672 (42.47) |
| 20 | .859 (21.82) | .125 (3.18) | 2.156 (54.76) | 1.719 (43.66) |
| 21 | .688 (17.48) | .125 (3.18) | 2.109 (53.57) | 1.672 (42.47) |
| 24 | .969 (24.61) | .125 (3.18) | 2.281 (57.94) | 1.844 (46.84) |
| 25 | .859 (21.82) | .125 (3.18) | 2.281 (57.94) | 1.656 (42.06) |
NOTES
- Dimensions are in inches.
- Metric equivalents are given for information only.
- Unless otherwise specified tolerances are ±.016 inch (0.41 mm).
- Break sharp edges .and remove all hanging burrs and slivers.
- Machined surfaces shall be finished to 125µ in Ra, forged surfaces shall be 250µ inches Ra, unless otherwise specified on the figures. Surface finish shall be in accordance with ASME B46.1.
- For design features purposes, this standard takes precedence over documents referenced herein.
- Referenced documents shall be of the issue in effect on date of invitation for bid.
REQUIREMENTS
Dimensions and configuration. The elbow dimensions and configuration shall be in accordance with figure 1.
Materials and finishes shall be in accordance with SAE-AS4843/2, see table I for material and finish code.
TABLE I. Material and finish codes.
| Material and finish code |
Material | Protective chemical finish 3/ 4/ |
|---|---|---|
| No code 1/ | Copper alloy, type 377 forging in accordance with ASTM B124/B124M or half hard forging or bar in accordance with ASTM B138/B138M or bar in accordance with SAE-AMS4614. | No finish. |
| BC 1/ | Copper alloy, type 377 forging in accordance with ASTM B124/B124M or half hard forging or bar in accordance with ASTM B138/B138M or bar in accordance with SAE-AMS4614. | Cadmium in accordance with SAE-AMS-QQ-P-416, type II, class 3. |
| D 2/ | Type 2014-T6 aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 or SAE-AMS4133, or type 2024-T6 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6, or type 2024-T851 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6 or SAE-AMS4339. | Anodize in accordance with SAE-AMS2472 or MIL-A-8625, type II, class 2, dye blue, duplex seal in accordance with procurement specification. |
| DV 2/ | Type 2014-T6 aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 or SAE-AMS4133, or type 2024-T6 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6, or type 2024-T851 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6 or SAE-AMS4339. | High purity aluminum in accordance with MIL-DTL-83488, class 3, type II with maximum coating thickness of .0005 inch. Glass bead peen pressure shall be 25 psi (1.72 bar) maximum. |
| J | Type 304 corrosion resistant steel forging or bar in accordance with SAE-AMS-QQ-S-763 or SAE-AMS5639. | Passivate in accordance with SAE-AMS2700, type VI or VII. |
| K | Type 316 corrosion resistant steel forging or bar in accordance with SAE-AMS-QQ-S-763 or SAE-AMS5648. | Passivate in accordance with SAE-AMS2700, type VI or VII. |
| R | Type 321 corrosion resistant steel forging or bar in accordance with SAE-AMS-QQ-S-763 or SAE-AMS5645. | Passivate in accordance with SAE-AMS2700, type VI or VII. |
| W 2/ | Type 7075-T73 aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 or SAE-AMS4141, or type 7075-T73 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/9, in accordance with type 7075-T7351 Aluminum alloy bar in accordance with SAE-AMS4124. | Anodize in accordance with SAE-AMS2472 or MIL-A-8625, type II, class 2, dye brown similar to color SAE-AMS-STD-595/10080, duplex seal in accordance with procurement specification. |
| WV 2/ | Type 7075-T73 aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 or SAE-AMS4141, or type 7075-T73 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/9, in accordance with type 7075-T7351 Aluminum alloy bar in accordance with SAE-AMS4124. | High purity aluminum in accordance with MIL-DTL-83488, class 3, type II with maximum coating thickness of .0005 inch. Glass bead peen pressure shall be 25 psi (1.72 bar) maximum. |
| T 3/ | Titanium | Anodize in accordance with SAE-AMS2488, type 2. |
1/ Material code was dash on previous revisions, changed to agree with SAE-ARP1590.
2/ Aluminum code D is inactivated, use code W.
3/ Titanium and cadmium shall not be used in oxygen systems.
4/ Cadmium shall not be used in potable water systems.
Oxygen systems for aerospace, shipboard, and ground support equipment. Parts for use on oxygen systems shall be identified in the PIN as code “A” and shall be furnished cleaned, packaged, and labeled in accordance with SAE-AS611 to a process approved by the user.
Guidance on use of alternative parts with less hazardous or non-hazardous materials. This specification provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application.
Marking: Part shall be permanently marked with the AN PIN, and include the manufacturers CAGE, name, or trademark.
Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.
Referenced documents shall be of the issue in effect on date of invitations for bid.
PART IDENTIFICATION NUMBER (PIN) SPECIFICATION
The PIN consists of the prefix “AN”, specification sheet number, dash number for tube and port size, material finish code letter(s) and blank of “A” for oxygen cleaning requirements. Unassigned PIN’s shall not be used.
PIN examples: AN844-4W indicates a 45° elbow 1/4 inch tube and hose size, aluminum alloy 7075-T73.
AN844-4WV indicates a 45° elbow 1/4 inch tube and hose size, aluminum alloy 7075-T73 finish with high purity aluminum.
AN844-4WA indicates a 45° elbow 1/2 inch tube and hose size, aluminum alloy 7075-T73 for use on oxygen systems.
SUPERSESSION DATA
The aluminum “D” designator has been replaced by the “W” designator.
Table II provides a detailed cross-reference of AN844 PINs and replacement SAE-AS5186 PINs. Users are cautioned to evaluate replacements for their particular application.
CAUTION: The superseding information is valid as of the date of this specification and may be superseded by subsequent revisions of the superseding document.
TABLE II. Cross-reference data. 1/
| AN PIN Inactive part |
Hose Size |
Pipe Size |
AS PIN 2/ Active part |
|---|---|---|---|
| AN844-4 | 0.250 | 0.125 | AS5186B0402 |
| AN844-4D | 0.250 | 0.125 | AS5186W0402 |
| AN844-4R | 0.250 | 0.125 | AS5186R0402 |
| AN844-4S | 0.250 | 0.125 | AS5186R0402 |
| AN844-4W | .2500 | 0.125 | AS5186W0402 |
| AN844-6 | 0.375 | 0.250 | AS5186B0604 |
| AN844-6D | 0.375 | 0.250 | AS5186W0604 |
| AN844-6R | 0.375 | 0.250 | AS5186R0604 |
| AN844-6S | 0.375 | 0.250 | AS5186R0604 |
| AN844-6W | 0.375 | 0.250 | AS5186W0604 |
| AN844-8 | 0.500 | 0.375 | AS5186B0806 |
| AN844-8D | 0.500 | 0.375 | AS5186W0806 |
| AN844-8R | 0.500 | 0.375 | AS5186R0806 |
| AN844-8S | 0.500 | 0.375 | AS5186R0806 |
| AN844-8W | 0.500 | 0.375 | AS5186W0806 |
| AN844-10 | 0.625 | 0.500 | AS5186B1008 |
| AN844-10D | 0.625 | 0.500 | AS5186W1008 |
| AN844-10R | 0.625 | 0.500 | AS5186R1008 |
| AN844-10S | 0.625 | 0.500 | AS5186R1008 |
| AN844-10W | 0.625 | 0.500 | AS5186W1008 |
| AN844-12 | 0.750 | 0.750 | AS5186B1212 |
| AN844-12D | 0.750 | 0.750 | AS5186W1212 |
| AN844-12R | 0.750 | 0.750 | AS5186R1212 |
| AN844-12S | 0.750 | 0.750 | AS5186R1212 |
| AN844-12W | 0.750 | 0.750 | AS5186W1212 |
| AN844-16 | 1.000 | 0.750 | AS5186B1612 |
| AN844-16D | 1.000 | 0.750 | AS5186W1612 |
| AN844-16R | 1.000 | 0.750 | AS5186R1612 |
| AN844-16S | 1.000 | 0.750 | AS5186R1612 |
| AN844-16W | 1.000 | 0.750 | AS5186W1612 |
| AN844-17 | 1.000 | 1.000 | AS5186B1616 |
| AN844-17D | 1.000 | 1.000 | AS5186W1616 |
| AN844-17R | 1.000 | 1.000 | AS5186R1616 |
| AN844-17S | 1.000 | 1.000 | AS5186R1616 |
| AN844-17W | 1.000 | 1.000 | AS5186W1616 |
| AN844-20 | 1.250 | 1.250 | AS5186B2020 |
| AN844-20D | 1.250 | 1.250 | AS5186W2020 |
| AN844-20R | 1.250 | 1.250 | AS5186R2020 |
| AN844-20S | 1.250 | 1.250 | AS5186R2020 |
| AN844-20W | 1.250 | 1.250 | AS5186W2020 |
| AN844-21 | 1.250 | 1.000 | AS5186B2016 |
| AN844-21D | 1.250 | 1.000 | AS5186W2016 |
| AN844-21R | 1.250 | 1.000 | AS5186R2016 |
| AN844-21S | 1.250 | 1.000 | AS5186R2016 |
| AN844-21W | 1.250 | 1.000 | AS5196W2016 |
| AN844-24 | 1.500 | 1.500 | AS5186B2424 |
| AN844-24D | 1.500 | 1.500 | AS5186W2424 |
| AN844-24R | 1.500 | 1.500 | AS5186R2424 |
| AN844-24S | 1.500 | 1.500 | AS5186R2424 |
| AN844-24W | 1.500 | 1.500 | AS5186W2424 |
| AN844-25 | 1.500 | 1.250 | AS5186B2420 |
| AN844-25D | 1.500 | 1.250 | AS5186W2420 |
| AN844-25R | 1.500 | 1.250 | AS5186R2420 |
| AN844-25S | 1.500 | 1.250 | AS5186R2420 |
| AN844-25W | 1.500 | 1.250 | AS5186W2420 |
1/ For new design use material designator R and W.
2/ SAE “B” designator for copper alloy parts can be either “no finish” or “cadmium plated”. This makes determination of hazardous materials more difficult and disposing of hazardous materials more laborious.
GENERAL GUIDANCE
Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes.