DETAIL SPECIFICATION SHEET
ELBOW, TUBE TO HOSE, 45 DEGREE
INCH-POUND · AN839 Rev 9 w/Amendment 1 · 18 November 2024 · Superseding AN839 Rev 9, 1 October 2014 · AMSC N/A · FSC 4730
FIGURE 1. 45°Elbow dimensions and configurations.

FIGURE 1. 45°Elbow dimensions and configurations – Continued.
| Dash number |
Hose ID inches (mm) |
Tube OD inches (mm) |
Thread T SAE-AS8879 |
A Approx inches (mm) |
B Approx inches (mm) |
|---|---|---|---|---|---|
| 4 | .250 (6.35) | .250 (6.35) | .4375-20UNJF-3A | .219 (5.56) | .250 (6.35) |
| 6 | .375 (9.53) | .375 (9.53) | .5625-18UNJF-3A | .281 (7.14) | .375 (9.53) |
| 8 | .500 (12.70) | .500 (12.70) | .7500-16UNJF-3A | .344 (8.74) | .438 (11.13) |
| 10 | .625 (15.88) | .625 (15.88) | .8750-14UNJF-3A | .438 (11.13) | .500 (12.70) |
| 12 | .750 (19.05) | .750 (19.05) | 1.0625 -12UNJF-3A | .500 (12.70) | .566 (14.38) |
| 16 | 1.000 (25.40) | 1.000 (25.40) | 1.3125 -12UNJ-3A | .563 (14.30) | .688 (17.48) |
| 20 | 1.250 (31.75) | 1.250 (31.75) | 1.6250 -12UNJF-3A | .688 (17.48) | 1.000 (25.40) |
| 24 | 1.500 (38.10) | 1.500 (38.10) | 1.8750 -12UNJF-3A | .750 (19.05) | 1.125 (28.58) |
| Dash number |
C dia. inches (mm) |
D +.047 (1.19) -.000 inches (mm) |
E Radius inches (mm) |
F +.047 (1.19) -.000 inches (mm) |
|---|---|---|---|---|
| 4 | .438 (11.13) | 1.688 (42.88) | .063 (1.60) | 1.422 (36.12) |
| 6 | .566 (14.38) | 1.719 (43.66) | 1.563 (39.70) | |
| 8 | .750 (19.05) | 1.750 (44.45) | .094 (2.39) | 1.828 (46.43) |
| 10 | .875 (22.23) | 1.797 (45.64) | 2.047 (51.99) | |
| 12 | 1.063 (27.00) | 1.828 (46.43) | 2.281 (57.94) | |
| 16 | 1.313 (33.35) | 1.890 (48.01) | .125 (3.18) | 2.391 (60.73) |
| 20 | 1.625 (41.28) | 1.969 (50.01) | 2.547 (64.69) | |
| 24 | 1.875 (47.63) | 2.031 (51.59) | 2.672 (67.87) |
| Dash number |
H Radius inches (mm) |
J +.047 (1.19) -.000 inches (mm) |
K inches (mm) |
M +.047 (1.19) -.000 inches (mm) |
|---|---|---|---|---|
| 4 | .063 (1.60) | 1.750 (44.45) | .438 (11.13) | 1.468 (37.29) |
| 6 | .094 (2.39) | 1.797 (45.64) | .563 (14.30) | 1.609 (40.87) |
| 8 | 1.813 (46.05) | .750 (19.05) | 1.938 (49.23) | |
| 10 | .125 (3.18) | 1.875 (47.63) | .875 (22.23) | 2.172 (55.17) |
| 12 | 1.953 (49.61) | 1.063 (27.00) | 2.422 (61.52) | |
| 16 | 2.047 (51.99) | 1.313 (33.35) | 2.593 (65.86) | |
| 20 | .188 (4.78) | 2.172 (55.17) | 1.625 (41.28) | 2.797 (71.04) |
| 24 | 2.281 (57.94) | 1.875 (47.63) | 2.969 (75.41) |
NOTES
- Dimensions are in inches.
- Metric equivalents are given for information only.
- Unless otherwise specified tolerances are ±.016 inch (0.41 mm).
- Break sharp edges and remove all hanging burrs and slivers
- Machined surfaces shall be finished to 125µ-in Ra, forged surfaces shall be 250µ-in Ra, unless otherwise specified on the figures. Surface finish shall be in accordance with ASME B46.1.
- For design features purposes, this standard takes precedence over documents referenced herein.
REQUIREMENTS
Dimensions and configuration shall be in accordance with figure 1.
Installation shall be in accordance with MS21344.
Materials and finishes: Unless otherwise specified materials and finishes shall be in accordance with SAE-AS4843; see table I for material/finish code.
TABLE I. Material and finish code letters.
| Material and finish code |
Material | Protective chemical finish 3/ |
|---|---|---|
| B 1/ | Copper alloy, type 377 forging in accordance with ASTM B124/B124M or half hard forging or bar in accordance with ASTM B138/B138M or bar in accordance with SAE-AMS4614. | No finish. |
| BC 1/ | Copper alloy, type 377 forging in accordance with ASTM B124/B124M or half hard forging or bar in accordance with ASTM B138/B138M or bar in accordance with SAE-AMS4614. | Cadmium in accordance with SAE-AMS-QQ-P-416, type II, class 3. |
| D 2/ | Type 2014-T6 aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 or SAE-AMS4133, or type 2024-T6 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6, or type 2024-T851 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6 or SAE-AMS4339. | Anodize in accordance with SAE-AMS2472 or MIL-PRF-8625, type II, class 2, dye blue, duplex seal in accordance with procurement specification. |
| DV 2/ | Type 2014-T6 aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 or SAE-AMS4133, or type 2024-T6 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6, or type 2024-T851 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6 or SAE-AMS4339. | High purity aluminum in accordance with MIL-DTL-83488, class 3, type II with maximum coating thickness of .0005 inch. Glass bead peen pressure shall be 25 psi (1.72 bar) maximum. |
| J | Type 304 corrosion resistant steel forging or bar in accordance with SAE-AMS-QQ-S-763 or SAE-AMS5639. | Passivate in accordance with SAE-AMS2700, type VI or VII. |
| K | Type 316 corrosion resistant steel forging or bar in accordance with SAE-AMS-QQ-S-763 or SAE-AMS5648. | Passivate in accordance with SAE-AMS2700, type VI or VII. |
| R | Type 321 corrosion resistant steel forging or bar in accordance with SAE-AMS-QQ-S-763 or SAE-AMS5645. | Passivate in accordance with SAE-AMS2700, type VI or VII. |
| W 2/ | Type 7075-T73 aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 or SAE-AMS4141, or type 7075-T73 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/9, in accordance with type 7075-T7351 Aluminum alloy bar in accordance with SAE-AMS4124. | Anodize in accordance with SAE-AMS2472 or MIL-PRF-8625, type II, class 2, dye brown similar to color 10080 in accordance with SAE AMS-STD-595, duplex seal in accordance with procurement specification. |
| WV 2/ | Type 7075-T73 aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 or SAE-AMS4141, or type 7075-T73 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/9, in accordance with type 7075-T7351 Aluminum alloy bar in accordance with SAE-AMS4124. | High purity aluminum in accordance with MIL-DTL-83488, class 3, type II with maximum coating thickness of .0005 inch. Glass bead peen pressure shall be 25 psi (1.72 bar) maximum. |
1/ Material code was dash on previous revisions, changed to agree with SAE-ARP1590.
2/ Aluminum code D is inactivated, use code W.
3/ Cadmium shall not be used in potable water systems.
Oxygen systems for aerospace, shipboard, and ground support equipment. Parts for use in oxygen systems (O2) shall be identified in the PIN as code “A” and shall be furnished cleaned, packaged, and labeled in accordance with SAE-AS611 to a process approved by the user.
Marking: Part shall be permanently marked with the AN PIN, and include the manufacturers CAGE, name, or trademark.
Guidance on use of alternative parts with less hazardous or non-hazardous materials. This specification provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application.
Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.
Referenced documents shall be of the issue in effect on date of invitations for bid.
PART IDENTIFICATION NUMBER (PIN) SPECIFICATION
The PIN consists of the prefix “AN”, specification sheet number, dash number for hose and flared tube size, material finish code letter(s) and blank or “A” for oxygen cleaning requirements. Unassigned PIN’s shall not be used.
PIN example: AN839-8K indicates a 45° elbow, tube to hose, .500 inches (12.70 mm), CRES alloy.
SUPERSESSION DATA
Canceled AN PIN and superseding AN PIN see table II.
TABLE II. Superseding AN PIN.
| Canceled AN PIN |
Hose Size |
Pipe Size |
Superseding AN PIN Inactive part |
|---|---|---|---|
| AN839-4 | 0.250 | 0.125 | AN839-4B |
| AN839-6 | 0.375 | 0.250 | AN839-6B |
| AN839-8 | 0.500 | 0.375 | AN839-8B |
| AN839-10 | 0.625 | 0.500 | AN839-10B |
| AN839-12 | 0.750 | 0.750 | AN839-12B |
| AN839-16 | 1.000 | 0.750 | AN839-16B |
| AN839-20 | 1.250 | 1.250 | AN839-20B |
| AN839-24 | 1.500 | 1.500 | AN839-24B |
| AN839-4S | 0.250 | 0.125 | AN839-4R |
| AN839-6S | 0.375 | 0.250 | AN839-6R |
| AN839-8S | 0.500 | 0.375 | AN839-8R |
| AN839-10S | 0.625 | 0.500 | AN839-10R |
| AN839-12S | 0.750 | 0.750 | AN839-12R |
| AN839-16S | 1.000 | 0.750 | AN839-16R |
| AN839-20S | 1.250 | 1.250 | AN839-20R |
| AN839-24S | 1.500 | 1.500 | AN839-24R |
Table III provides a detailed cross-reference of AN839 PINs and replacement SAE-AS5182 PINs. Users are cautioned to evaluate replacements for their particular application.
Metal cracking due to high temperatures CRES alloy 347 “S” designator has been replaced by CRES alloy 321 “R” designator.
CAUTION: The superseding information is valid as of the date of this specification and may be superseded by subsequent revisions of the superseding document.
TABLE III. Cross-reference data. 1/ 2/
| AN PIN Inactive part |
Hose Size |
Pipe Size |
AS PIN Active part |
|---|---|---|---|
| AN839-4B | 0.250 | 0.250 | AS5182B04 |
| AN839-4BC | 0.250 | 0.250 | None |
| AN839-4D | 0.250 | 0.250 | AS5182W04 |
| AN839-4J | 0.250 | 0.250 | AS5182J04 |
| AN839-4K | 0.250 | 0.250 | AS5182K04 |
| AN839-4R | 0.250 | 0.250 | AS5182R04 |
| AN839-4S | 0.250 | 0.250 | AS5182R04 |
| AN839-4W | 0.250 | 0.250 | AS5182W04 |
| AN839-4WV | 0.250 | 0.250 | AS5182WV04 |
| AN839-6B | 0.375 | 0.375 | AS5182B06 |
| AN839-6BC | 0.375 | 0.375 | None |
| AN839-6D | 0.375 | 0.375 | AS5182W06 |
| AN839-6J | 0.375 | 0.375 | AS5182J06 |
| AN839-6K | 0.375 | 0.375 | AS5182K06 |
| AN839-6R | 0.375 | 0.375 | AS5182R06 |
| AN839-6S | 0.375 | 0.375 | AS5182R06 |
| AN839-6W | 0.375 | 0.375 | AS5182W06 |
| AN839-6WV | 0.375 | 0.375 | AS5182WV06 |
| AN839-8B | 0.500 | 0.500 | AS5182B08 |
| AN839-8BC | 0.500 | 0.500 | None |
| AN839-8D | 0.500 | 0.500 | AS5182W08 |
| AN839-8J | 0.500 | 0.500 | AS5182J08 |
| AN839-8K | 0.500 | 0.500 | AS5182K08 |
| AN839-8R | 0.500 | 0.500 | AS5182R08 |
| AN839-8S | 0.500 | 0.500 | AS5182R08 |
| AN839-8W | 0.500 | 0.500 | AS5182W08 |
| AN839-8WV | 0.500 | 0.500 | AS5182WV08 |
| AN839-10B | 0.625 | 0.625 | AS5182B10 |
| AN839-10BC | 0.625 | 0.625 | AS5182B10 |
| AN839-10D | 0.625 | 0.625 | AS5182W10 |
| AN839-10J | 0.625 | 0.625 | AS5182J10 |
| AN839-10K | 0.625 | 0.625 | AS5182K10 |
| AN839-10R | 0.625 | 0.625 | AS5182R10 |
| AN839-10S | 0.625 | 0.625 | AS5182R10 |
| AN839-10W | 0.625 | 0.625 | AS5182W10 |
| AN839-10WV | 0.625 | 0.625 | AS5182WV10 |
| AN839-12 | 0.750 | 0.750 | AS5182B12 |
| AN839-12BC | 0.750 | 0.750 | None |
| AN839-12D | 0.750 | 0.750 | AS5182W12 |
| AN839-12J | 0.750 | 0.750 | AS5182J12 |
| AN839-12K | 0.750 | 0.750 | AS5182K12 |
| AN839-12R | 0.750 | 0.750 | AS5182R12 |
| AN839-12S | 0.750 | 0.750 | AS5182R12 |
| AN839-12W | 0.750 | 0.750 | AS5182W12 |
| AN839-12Wv | 0.750 | 0.750 | AS5182Wv12 |
| AN839-16B | 1.000 | 1.000 | AS5182B16 |
| AN839-16BC | 1.000 | 1.000 | None |
| AN839-16D | 1.000 | 1.000 | AS5182W16 |
| AN839-16J | 1.000 | 1.000 | AS5182J16 |
| AN839-16K | 1.000 | 1.000 | AS5182K16 |
| AN839-16R | 1.000 | 1.000 | AS5182R16 |
| AN839-16S | 1.000 | 1.000 | AS5182R16 |
| AN839-16W | 1.000 | 1.000 | AS5182W16 |
| AN839-16WV | 1.000 | 1.000 | AS5182WV16 |
| AN839-20B | 1.250 | 1.250 | AS5182B20 |
| AN839-20BC | 1.250 | 1.250 | None |
| AN839-20D | 1.250 | 1.250 | AS5182W16 |
| AN839-20J | 1.250 | 1.250 | AS5182J20 |
| AN839-20K | 1.250 | 1.250 | AS5182K20 |
| AN839-20R | 1.250 | 1.250 | AS5182R20 |
| AN839-20S | 1.250 | 1.250 | AS5182R20 |
| AN839-20W | 1.250 | 1.250 | AS5181W20 |
| AN839-20WV | 1.250 | 1.250 | AS5181WV20 |
| AN839-24B | 1.500 | 1.500 | AS5182B24 |
| AN839-24BC | 1.500 | 1.500 | None |
| AN839-24D | 1.500 | 1.500 | AS5182W24 |
| AN839-24J | 1.500 | 1.500 | AS5182J24 |
| AN839-24K | 1.500 | 1.500 | AS5182K24 |
| AN839-24R | 1.500 | 1.500 | AS5182R24 |
| AN839-24S | 1.500 | 1.500 | AS5182R24 |
| AN839-24W | 1.500 | 1.500 | AS5182W24 |
| AN839-24WV | 1.500 | 1.500 | AS5182WV24 |
1/ For new design use material designators R and W.
2/ SAE “B” designator for copper alloy parts can be either no finish or cadmium plate.
GENERAL GUIDANCE
Amendment notations. The margins of this specification are marked with vertical lines to indicate modifications generated by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations.