DETAIL SPECIFICATION SHEET
ELBOW, TUBE TO HOSE, 90°
INCH-POUND · AN838 Rev 9 w/Amendment 2 · 4 December 2023 · Superseding AN838 Rev 9 w/Amendment 1, 27 February 2013 · AMSC N/A · FSC 4730
FIGURE 1. 90°Elbow.

FIGURE 1. 90°Elbow – Continued.
| Dash number |
Hose ID inches (mm) |
Tube size inches (mm) |
Thread T SAE-AS8879 |
A Approx inches (mm) |
B Approx inches (mm) |
|---|---|---|---|---|---|
| 4 | .250 (6.35) | .250 (6.35) | .4375-20UNJF-3A | .250 (6.25) | .313 (7.95) |
| 6 | .375 (9.53) | .375 (9.53) | .5625-18UNJF-3A | .313 (7.95) | .500 (12.70) |
| 8 | .500 (12.70) | .500 (12.70) | .7500-16UNJF-3A | .438 (11.13) | .625 (15.88) |
| 10 | .625 (15.88) | .625 (15.88) | .8750-14UNJF-3A | .438 (11.13) | .750 (19.05) |
| 12 | .750 (19.05) | .750 (19.05) | 1.0625 -12UNJ-3A | .500 (12.70) | .938 (23.83) |
| 16 | 1.000 (25.40) | 1.000 (25.40) | 1.3125 -12UNJ-3A | .563 (14.30) | 1.000 (25.40) |
| 20 | 1.250 (31.75) | 1.250 (31.75) | 1.6250 -12UNJ-3A | .563 (14.30) | 1.250 (37.75) |
| 24 | 1.500 (38.10) | 1.500 (38.10) | 1.8750 -12UNJ-3A | .625 (15.88) | 1.500 (38.10) |
| Dash number |
C Dia. inches (mm) |
D +.047 (1.19) -.000 inches (mm) |
E Radius inches (mm) |
F +.047 (1.19) -.000 inches (mm) |
|---|---|---|---|---|
| 4 | .438 (11.13) | 1.844 (46.84) | .063 (1.60) | 1.563 (39.70) |
| 6 | .563 (14.30) | 1.938 (49.23) | 1.734 (44.04) | |
| 8 | .750 (19.05) | 2.031 (51.59) | .094 (2.39) | 2.031 (51.59) |
| 10 | .875 (22.23) | 2.094 (53.19) | 2.281 (57.94) | |
| 12 | 1.063 (27.00) | 2.250 (57.15) | 2.563 (65.10) | |
| 16 | 1.313 (33.35) | 2.375 (60.33) | .125 (3.18) | 2.688 (68.28) |
| 20 | 1.625 (41.28) | 2.531 (64.29) | 2.922 (74.22) | |
| 24 | 1.875 (47.63) | 2.656 (67.46)_ | 3.063 (77.80) |
| Dash number |
H Radius inches (mm) |
J +.047 (1.19) -.000 inches (mm) |
K inches (mm) |
M +.047 (1.19) -.000 inches (mm) |
|---|---|---|---|---|
| 4 | .063 (1.57) | 1.906 (48.41) | .438 (11.13) | 1.594 (40.49) |
| 6 | .094 (2.39) | 2.000 (50.80) | .563 (14.30) | 1.766 (44.86) |
| 8 | 2.109 (53.57) | .750 (19.05) | 2.109 (53.57) | |
| 10 | .125 (3.18) | 2.172 (55.17) | .875 (22.23) | 2.391 (60.73) |
| 12 | 2.375 (60.33) | 1.063 (27.00) | 2.688 (68.28) | |
| 16 | 2.547 (64.69) | 1.313 (33.35) | 2.875 (73.03) | |
| 20 | .188 (4.78) | 2.766 (70.26) | 1.625 (41.28) | 3.156 (80.16) |
| 24 | 2.938 (74.63) | 1.875 (47.63) | 3.359 (85.32) |
NOTES
- Dimensions are in inches.
- Metric equivalents are given for information only.
- Unless otherwise specified tolerances are ±.010 inch (0.25 mm).
- Break sharp edges .and remove all hanging burrs and slivers
- Machined surfaces shall be finished to 125µ in Ra, forged surfaces shall be 250µ inches Ra, unless otherwise specified on the figures. Surface finish shall be in accordance with ASME B46.1.
- For design features purposes, this standard takes precedence over documents referenced herein.
REQUIREMENTS
Dimensions and configuration shall be in accordance with figure 1.
Installation shall be in accordance with MS21344.
Materials and finishes shall be in accordance with SAE-AS4843/1, see table I for material and finish code.
TABLE I. Material and finish code letters.
| Material code |
Material | Protective chemical finish 3/ 4/ |
|---|---|---|
| No code 1/ | Copper alloy, type 377 forging in accordance with ASTM B124/B124M or half hard forging or bar in accordance with ASTM B138/B138M or bar in accordance with SAE-AMS4614 | No finish |
| BC 1/ | Copper alloy, type 377 forging in accordance with ASTM B124/B124M or half hard forging or bar in accordance with ASTM B138/B138M or bar in accordance with SAE-AMS4614 | Cadmium in accordance with SAE-AMS-QQ-P-416, type II, class 3 |
| D 2/ | Type 2014-T6 aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 or SAE-AMS4133, or type 2024-T6 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6, or type 2024-T851 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6 or SAE-AMS4339 | Anodize in accordance with SAE-AMS2472 or MIL-PRF-8625, type II, class 2, dye blue, duplex seal in accordance with procurement specification. |
| DV 2/ | Type 2014-T6 aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 or SAE-AMS4133, or type 2024-T6 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6, or type 2024-T851 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/6 or SAE-AMS4339 | High purity aluminum in accordance with MIL-DTL-83488, class 3, type II with maximum coating thickness of .0005 inch. Glass bead peen pressure shall be 25 psi (1.72 bar) maximum. |
| J | Type 304 corrosion resistant steel forging or bar in accordance with SAE-AMS-QQ-S-763 or SAE-AMS5639 | Passivate in accordance with SAE-AMS2700, type VI or VII |
| K | Type 316 corrosion resistant steel forging or bar in accordance with SAE-AMS-QQ-S-763 or SAE-AMS5648 | Passivate in accordance with SAE-AMS2700, type VI or VII |
| R | Type 321 corrosion resistant steel forging or bar in accordance with SAE-AMS-QQ-S-763 or SAE-AMS5645. | Passivate in accordance with SAE-AMS2700, type VI or VII |
| W 2/ | Type 7075-T73 aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 or SAE-AMS4141, or type 7075-T73 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/9, in accordance with type 7075-T7351 Aluminum alloy bar in accordance with SAE-AMS4124. | Anodize in accordance with SAE-AMS2472 or MIL-PRF-8625, type II, class 2, dye brown similar to color 10080 in accordance with SAE AMS-STD-595, duplex seal in accordance with procurement specification. |
| WV 2/ | Type 7075-T73 aluminum alloy forging in accordance with SAE-AMS-QQ-A-367 or SAE-AMS4141, or type 7075-T73 aluminum alloy bar in accordance with SAE-AMS-QQ-A-225/9, in accordance with type 7075-T7351 Aluminum alloy bar in accordance with SAE-AMS4124. | High purity aluminum in accordance with MIL-DTL-83488, class 3, type II with maximum coating thickness of .0005 inch. Glass bead peen pressure shall be 25 psi (1.72 bar) maximum |
| T 3/ | Titanium | Anodize in accordance with SAE-AMS2488, type 2 |
1/ Material code was dash on previous revisions, changed to agree with SAE-ARP1590.
2/ Aluminum code D is inactivated, use code W.
3/ Titanium and cadmium shall not be used in oxygen systems.
4/ Cadmium shall not be used in potable water systems.
Oxygen systems for aerospace, shipboard, and ground support equipment. Parts for use on oxygen systems shall be identified in the PIN as code “A” and shall be furnished cleaned, packaged, and labeled in accordance with SAE-AS611 to a process approved by the user.
Marking: Part shall be permanently marked with the AN PIN, and include the manufacturers CAGE, name, or trademark.
PART IDENTIFICATION NUMBER (PIN) SPECIFICATION
The PIN consists of the prefix “AN” the specification sheet number, a dash number for tube and hose size, material code letter, finish code, and oxygen code. Unassigned PIN’s shall not be used.
PIN examples: AN838-4W indicates a 90° elbow 1/4 inch tube and hose size, aluminum alloy 7075-T73.
AN838-4WV indicates a 90° elbow 1/4 inch tube and hose size, aluminum alloy 7075-T73 finish with high purity aluminum.
AN838-4WA indicates a 90° elbow 1/2 inch tube and hose size, aluminum alloy 7075-T73 for use on oxygen systems.
SUPERSESSION DATA
Table II provides a detailed cross-reference of AN838 PINs and replacement SAE-AS5181 PINs. Users are cautioned to evaluate replacements for their particular application.
CAUTION: The superseding information is valid as of the date of this specification and may be superseded by subsequent revisions of the superseding document.
TABLE II. Cross-reference data. 1/
| AN PIN inactive for new design |
Hose Size |
Tube Size |
Replacement AS PIN for new design |
|---|---|---|---|
| AN838-4 | 0.250 | 0.250 | AS5181B04 |
| AN838-4D | 0.250 | 0.250 | AS5181W04 |
| AN838-4J | 0.250 | 0.250 | AS5181J04 |
| AN838-4K | 0.250 | 0.250 | AS5181K04 |
| AN838-4R | 0.250 | 0.250 | AS5181R04 |
| AN838-4S | 0.250 | 0.250 | AS5181R04 |
| AN838-4W | 0.250 | 0.250 | AS5181W04 |
| AN838-6 | 0.375 | 0.375 | AS5181B06 |
| AN838-6D | 0.375 | 0.375 | AS5181W06 |
| AN838-6J | 0.375 | 0.375 | AS5181J06 |
| AN838-6K | 0.375 | 0.375 | AS5181K06 |
| AN838-6R | 0.375 | 0.375 | AS5181R06 |
| AN838-6S | 0.375 | 0.375 | AS5181R06 |
| AN838-6W | 0.375 | 0.375 | AS5181W06 |
| AN838-8 | 0.500 | 0.500 | AS5181B08 |
| AN838-8D | 0.500 | 0.500 | AS5181W08 |
| AN838-8J | 0.500 | 0.500 | AS5181J08 |
| AN838-8K | 0.500 | 0.500 | AS5181K08 |
| AN838-8R | 0.500 | 0.500 | AS5181R08 |
| AN838-8S | 0.500 | 0.500 | AS5181R08 |
| AN838-8W | 0.500 | 0.500 | AS5181W08 |
| AN838-10 | 0.625 | 0.625 | AS5181B10 |
| AN838-10D | 0.625 | 0.625 | AS5181W10 |
| AN838-10J | 0.625 | 0.625 | AS5181J10 |
| AN838-10K | 0.625 | 0.625 | AS5181K10 |
| AN838-10R | 0.625 | 0.625 | AS5181R10 |
| AN838-10S | 0.625 | 0.625 | AS5181R10 |
| AN838-10W | 0.625 | 0.625 | AS5181W10 |
| AN838-12 | 0.750 | 0.750 | AS5181B12 |
| AN838-12D | 0.750 | 0.750 | AS5181W12 |
| AN838-12J | 0.750 | 0.750 | AS5181J12 |
| AN838-12K | 0.750 | 0.750 | AS5181K12 |
| AN838-12R | 0.750 | 0.750 | AS5181R12 |
| AN838-12S | 0.750 | 0.750 | AS5181R12 |
| AN838-12W | 0.750 | 0.750 | AS5181W12 |
| AN838-16 | 1.000 | 1.000 | AS5181B16 |
| AN838-16D | 1.000 | 1.000 | AS5181W16 |
| AN838-16J | 1.000 | 1.000 | AS5181J16 |
| AN838-16K | 1.000 | 1.000 | AS5181K16 |
| AN838-16R | 1.000 | 1.000 | AS5181R16 |
| AN838-16S | 1.000 | 1.000 | AS5181R16 |
| AN838-16W | 1.000 | 1.000 | AS5181W16 |
| AN838-20 | 1.250 | 1.250 | AS5181B20 |
| AN838-20D | 1.250 | 1.250 | AS5181W20 |
| AN838-20J | 1.250 | 1.250 | AS5181J20 |
| AN838-20K | 1.250 | 1.250 | AS5181K20 |
| AN838-20R | 1.250 | 1.250 | AS5181R20 |
| AN838-20S | 1.250 | 1.250 | AS5181R20 |
| AN838-20W | 1.250 | 1.250 | AS5181W20 |
| AN838-24 | 1.500 | 1.500 | AS5181B24 |
| AN838-24D | 1.500 | 1.500 | AS5181W24 |
| AN838-24J | 1.500 | 1.500 | AS5181J24 |
| AN838-24K | 1.500 | 1.500 | AS5181K24 |
| AN838-24R | 1.500 | 1.500 | AS5181R24 |
| AN838-24S | 1.500 | 1.500 | AS5181R24 |
| AN838-24W | 1.500 | 1.500 | AS5181W24 |
1/ For new design use material designators R and W.
GENERAL GUIDANCE
Amendment notations. The margins of this specification are marked with vertical lines to indicate modifications generated by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations.